您要查找的是不是：
- The Effect of SRM's Mass on the Thrust Measurement with a Vertical Test Fixture 立式试车时固体发动机质量对推力测量的影响
- Design and Analysis of Dynamic Characteristics of Vertical Test Fixture for Short-time and High-Thrust Motor 短时大推力发动机立式试车架动态特性设计与分析
- To design, fabricate and repair test fixture. 设计;制作和修理测试机架.
- To plan and control the assumption of test fixture materials. 计划和控制测试机架原材料。
- The requirement for a good test fixture is maximum stiffness for the lightest possible weight. 一台好的试验固紧装置应该是重量轻而刚度大。
- Have rich experience on test fixture building, able to build pneumatic controlled fixture is prefer. 具有丰富的测试治具制作经验,懂气动控制治具制作优先。
- To prevent transients, always turn the source off while switching contacts in and out of the test fixture. 为了避免发生瞬变现象，一定要先将电流源关闭，然后再把接点接入测试夹具或将其断开。
- DUT is placed in test fixture such a diode, transistors, microstrip circuit and so on. 被测件放在测试夹具里，如二极管、晶体管、微带电路等。
- Figure 2-12 shows a high mega-ohm resistor (RDUT) supported on two insulators mounted in a metal test fixture. 图2-12示出了测试夹具上由两个绝缘子支撑的高阻器（RDUT）。
- Again, it may be more economical to cut the cables in half, then permanently connect the cut ends to the test fixture. 同样，若将电缆分为两部分，然后将被截断的一端永久性地连接到测试夹具，则更经济。
- The first step to verify the system requires that resistors of known value be placed in the test fixture. 验证系统的第一步需要将一个已知阻值的电阻器置于测试夹具中。
- If mass-terminated cables are used, mating receptacles can be mounted at the test fixture. 如果采用接线头电缆，在夹具上则可以安装匹配插座。
- Use high-reliability, fail-safe interlock switches to disconnect power sources when a test fixture cover is opened. 采用高可靠性、自动防止故障的联锁开关，在夹具外罩被打开时能够自动断开电源。
- This paper introduces the test effects of the roadway support with yieldable legs including different construction on Vertical test stand,and analysed mechanics features and effect factors. 介绍了在立式巷道支架试验台上，对不同结构形式平顶形柱腿可缩金属支架的试验结果。分析了支架的力学特征和影响柱腿可缩性的因素。
- However, it may be more economical to cut mass-terminated cables in half and hardwire the individual wires to the test fixture. 然而，若将接线头电缆分为两部分，然后将独立的导线硬连接至夹具，则更加经济。
- The Model 8009 employs a safety interlock to prevent the high voltage from being applied to the electrode until the test fixture lid is closed. 8009型采用了一种安全互锁机构，在测试夹具的盖子关闭之前，高电压不能施加到电极上。
- Can be used for probe board and loading board of ICT、ATE and different kinds of functional test fixture, AOI plate fixture and other anti-static fixture or equipment. 用作ICT/ATE测试夹具针板、载板、各种功能测试夹具的针板和载板，以及AOI拖板治具和各种抗静电要求较高的治具或者设备。
- From the control box, burning me, burning lights, electromagnetic valve, high-pressure ignition, plastic goods test fixture, gas pipes and signal the line of control components. 由控制箱、燃烧箱、燃烧灯、电磁阀、高压点火器、塑料试品夹具、煤气管和信号控制线组成。
- If you are using a test fixture, keep the lid closed while power is applied to the device under test. Safe operation requires the use of a lid interlock. 如果使用测试夹具，当被测电路加有电源时，请保证外盖安装完好。为确保操作安全，需要使用一个外盖联锁。
- Oxygen gas transmission rate ( O2 GTR ) is determined after the package has been mounted on a test fixture and has equilibrated in the test environment. 氧气透过率（O2 GTR）是将包装物固定在测试装置上并在测试环境中达到平衡后测定的。
