您要查找的是不是：
- Parting line at the acceptable surface. 合模分布在合理可接受的表面。
- Parting line cleared and released properly? 分模线是否正确?
- Parting line locks are required on all molds. 琐模块所有的模具都需要。
- The sides are sectioned with a vertical parting behind each ear. 边与垂直一起区段在每只耳朵后面分开。
- The parting line tolerance for gib installation is +.000/-.002. 安装导板的分模线公差为+.;000/-
- Moulding machines, Moulding line, Vertical parting automatic shooting moulding line, Horizontal parting stripper shooting moulding line, Sand preparation system Resin sand line, Silicate-bonded sand line. Shot blaot cleaning equipment, Surface. 造型机,造型线,垂直分型、水平分型自动造型线,砂处理成套设备,树脂砂、水玻璃砂成套设备,中英合资抛丸清理机、表面强化设备。
- Now, subsection the right side with three vertical partings. 现在,小部份和三垂直的分别正确的边。
- An annular groove is at the outer surface of the insulated loop frame,which requires a vertical parting of the mould along the axis. 线圈绝缘框外侧有一圈凹槽,要求成型模具沿轴线垂直分型。
- When they erupt, diamonds are thrown out of the top in the lava or are left in the pipe, the central, vertical part of the volcano. 当火山爆发时,钻石被抛到熔岩的上部或者留在火山中部竖直的熔岩通道中。
- There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 产品的这个位置不能出模,我们打算做行位,在此面上会有分模线,你接受吗?
- Becasue of hand deflashing, please mark the parting line into the drawing, and please let me know then the flash size. 因为手遮光，请将分界线在图中标出来，并告诉确切尺寸。
- The vertical line meets the horizontal one here. 垂直线与水平线在此相交。
- Mould halves requiring accurate alignment of core and cavity, and shut off should have appropriate part line locks. 上、下模需要精确配合或有擦位的地方,模具一定要有直身锁。
- Follow this by subdividing the remaining parting at the front-left side of the diamond with three vertical partings. 藉由在和三垂直的分别钻石的前面留下的边细分剩余的分别跟随这。
- The parting line at ends of block should be designed such that any offset is in 1"increments for maintenance purposes on core. 考虑到动模维护需要,封胶面应有1”左右的偏移增量。
- Our company produce grey cast iron, ductile cast iron and other cast iron, for refrigerator compressor, ai conditioner compressor, automobile, underground, hydraulic and so on, by DISA vertical parting molding, permonent mold and other casting processes. 采用DISA垂直分型无箱射压造型、金属型等铸造方法,专业为制冷、汽车、地铁、液压等行业生产精细铸铁件。
- After subsectioning the fringe at the recession on either side, move to the left side section and subsection with three vertical partings. 在在任一边上的后退小部份边缘之后,以三垂直的分别移到左边的旁区段和小部份。
- The optimization parting direction was determined after all undercut features were distinguished, and the parting line and parting surface were confirmed accordingly. 通过侧凹特征的判别确定模具的优化脱模方向，并确定模具的分型线和分型面。
- Subdivide three vertical partings and sculpt alternately short, long and short lengths using 90 degree projection and a vertical finger position. 细分三垂直的分别而且雕刻交替短，长的和短长度使用90度发射和一个垂直的手指位置。
- The selection of parting line,the determination of round sprue runner diameter,the design of round sprue runner shape and pouring gate form were presented. 介绍了模具分型面的位置选择、圆形流道直径的确定、圆形流道形状的设计、浇口形式等。
