您要查找的是不是:
- valve lash adjusting screw 气门间隙调节螺钉
- Valve Gear and Valve Lash Adjustment of TOYOTA 2JZ-GE Engine 丰田2JZ-GE发动机气门驱动机构与气门间隙的调整
- Hydraulic Valve Lash Adjuster (HLA) and Valve Train with HLA 液压气门间隙调节器及有间隙调节器的气门机构的研究
- The high step moves from under the adjusting screw. 使高点从调节螺钉下移动。
- The adjusting screw rests on the high step of the cam. 调节螺钉落在凸轮高点上。
- To Readjust- Loosen lock nut on the adjusting screw. 重新调节:松开调节螺丝上的锁定螺母。
- Valve Lash Adjuster 气门间隙调节器又称液压挺杆
- To Readjust - Loosen lock nut on the adjusting screw. 重新调节:松开调节螺丝上的锁定螺母。
- Remove compression from spring by turning adjusting screw (1) counterclockwise. 通过反时针方向旋转调节螺丝(1)从弹簧上拆卸压缩件。
- Heavy duty adjusting screw. Adjusting screw is both slotted and knurled. 重型调节螺丝。调节螺丝既有槽也有花纹边。
- Remove adjuster lever, adjuster screw and spring. 拆卸调整器杆,调整器螺丝和弹簧。
- J. Vertical Shaft Fine Adjustment Screw. 垂直杆微调螺丝.
- To replace seat/ stem module shut off supply, loosen locknut and back off adjusting screw. 要更换阀座/杆模块,先关闭供应管道,松开锁紧螺母,退出调节螺丝。
- The oil bulk modulus reduction caused by aeration in the high pressure chamber of hydraulic lash adjusters (HLA) should be taken into account to accurately model and simulate a valve train with HLA. 为对有液压间隙调节器(HLA)的气门机构进行准确的动力学分析,应考虑HLA高压腔内混气的影响。
- Loosen the adjustment screw, and adjust the length of the link rod. 请拧松调整螺丝,拔出或插入连接杆进行调整。
- If valve clearance needs to be adjusted, loosen the locknut on rocker arm adjusting screw.Turn adjusting screw until feeler gauge slips with a slight drag. 如果气门间隙需要调节,松开摇臂调节螺丝上的防松螺母,转动调节螺丝直到测隙规滑动时稍带阻力为止。
- To replace seat/stem module shut off supply, loosen locknut and back off adjusting screw. 要更换阀座/阀杆模块,先关闭供应管道,松开锁紧螺母,退出调节螺丝。
- To clean or replace parts; shut off supply, loosen lock-nut and back off adjusting screw. 如果要清洗或更换部件,关闭供应管道,松开锁紧螺母,退出调节螺丝。
- Turn adjusting screw (1) clockwise to increase the delivery pressure, counterclockwise to lower it. 顺时针方向旋转调节螺丝(1)以增加输出压力,反时针方向旋转降低输出压力。
- Tighten adjustment screw to 3 N·m (30 in-lbs) torque. 拧紧调整螺丝到3 N·m (30 in-lbs)扭力。