您要查找的是不是：
- valve sealing cap 气门封帽
- Remove sealing cap from the discharge valve。When using discharge tube, please?screw it onto the outlet of valve, and tighten it. 旋下排液阀的盖子。如使用弯管，请将其套在阀门放料口的外螺纹上，并用手拧紧；
- Remove check valve and valve seal from booster. 从倍力器上卸去逆止阀和阀门密封。
- For ease of installation moisten seal cap with water or lubricant. 为安装方便,密封套可使用水或润滑剂来润滑。
- HF acid detecting paint to ensure valve sealing integrity. 氢氟酸检测漆，用于保证密封的整体性。
- Manifolds can be added to a control valve sealing device. 可以给阀组加一个阀的密封控制装置。
- Adopted liquid polysulfide prepolymer cured at high temperature for sealing cap at the first time. 首次采用液体聚硫橡胶制成预聚体再高温硫化成型,压制新型聚硫橡胶密封帽制品。
- DISCHARGE Remove the top filling lid.Unscrew and remove sealing cap from the discharge valve.Cut off Alnm foil. 排液打开顶部的灌装口盖，旋下阀门前端螺纹盖，撕开封闭用的铝膜;
- Push conduit with seal cap with slight twist fully into connector. (For safety reasons, retaining clip will not fit if seal cap is not fully installed. 将带密封套的软管完全推进接头。(如果密封套没有完全安装好,管卡将不能安装)
- Presents the development and use of new stainless steel heap welding technique for main steam valve sealing surface. 介绍了主蒸汽阀门密封面不锈钢堆焊新工艺的开发与利用。
- If the spacing between mating flanges is tight, the valve sealing surface should be coated with a lubricant to prevent distortion during installation. 如果配置的法兰之间的间隙过紧，则阀门密封面应该用润滑剂涂敷以防止在安装过程中产生扭曲变形。
- In the second part, the preliminary experience of plasma powder overlaying work with valve sealing surface is introduced. 第二部份介绍阀门密封面等离子粉末堆焊工作的初步经验。
- Before installation should completed clean inner of the pipeline, particles or sundries are not allowed to be contained in the medium to avoid the damage of valve sealing surface. 阀门安装前请将管路彻底清洗干净，介质中不能含有颗粒或杂物。以免损伤阀门密封面。
- Other cars use a sealed cap and have separate vacuum-and pressure-relief valves. 另一种类型的汽车使用密封式油箱盖，并带有一个独立的真空--压力减压阀。
- To introduce one kind of ball valve sealing structures which is formed through bringing pressure on the seat ring while the ball or disc is rolling towards the seat ring parallelly. 介绍了一种球体或球瓣向阀座平行滚动而压紧阀座形成密封的球阀密封结构。
- universal-joint oil seal cap ring 万向节油封帽环
- For2Cr13 valve sealing face by double glow plasma W alloying process,carburizing , quenching and tempering process, the results show its machining size is little, its hardness is high and its static pressure lifetime is long. 结果表明经双层辉光离子渗钨、渗碳和淬火回火处理的2Cr13阀门密封面加工量小、硬度高、静压寿命长。
- Replace the cylinder outlet seal and valve cap. 替换钢瓶排气口密封和阀门帽。
- Many ways to prevent leakage in the installation process, the choice of packing, sealing method of choice, good choice of valve sealing performance, are factors that must be taken into account. 防止泄漏的方法很多，在安装过程中，填料的选择、密封方法的选择、选用密封性能好的调节阀等，都是必须考虑的因素。
- The regulations and methods for valve base seal test, valve seal test, valve strength test, long term valve test, fatigue test and operating torque test were summed up in this article. 汇总了塑料阀门产品要求的阀座密封试验、阀体密封试验、阀体强度试验、阀门长期试验、疲劳强度试验和操作扭矩的规定和方法。
