您要查找的是不是：
- In order to effectively machine an orthogonal face gear,the geometrical design of tooth profile and the undercut condition for the gear are investigated via the enveloping method. 为了实现正交面齿轮的加工,采用包络法对正交面齿轮齿廓的几何设计方法和根切条件进行了研究。
- We are able to offer the tooth profile of chain and sprocket. 我们有能力提供各种形链和链轮。
- The equations of thecurvature,curvature radius on hypocycloid"s tooth profile are deduced. 在此基础上分析推导了各种型式的滚子链谐波传动的传动比计算公式。
- It is proofed with experiment that these is local sunken point in th e raised tooth profile of involute gear. 试验验证渐开线齿轮凸齿形上确实存在局部凹状。
- This paper discussed the relationship between the involute pitch of tooth root and tooth profile involute in hobbing. 本文阐述了滚刀滚齿时齿轮齿根过渡曲线的延长渐开线的等距线与齿轮齿形渐开线的关系。
- Based on the tooth profile curve equation of inner rotors in cycloidal pump, the formula for displacement calculation of the pump are derived. 根据摆线泵内转子的齿廓曲线方程,推导出了摆线泵的排量计算公式。
- The shaving stock of preshaving gears has direct influence on the shaving effect and the tooth profile of preshaving cutters. 剃前齿轮的留剃量形式直接影响剃齿效果及剃前刀具齿形。
- At last, the tooth profile is measured and the errors in tooth profile and aptness are evaluated by three coordinate measurement machine. 最后,利用三坐标测量机对进行仿真的锥齿轮廓面进行了测量,并评定了齿轮的齿形和接触迹误差,同时进行了齿轮副接触区域的运转实验。
- During ausform finishing process of hardened gears, there is plastic displacement of metal on the tooth surface and the distortion of tooth profile . 在齿轮热滚挤加工中,轮齿上的金属在强制挤压力的作用下沿齿面产生塑性流动,使齿形发生变化。
- Chamfering process of gear tooth profile and its function are introduced. By tooth profile chamfer, noise of gear transmission can be reduced. 通过对齿轮传动噪声产生原因的分析,介绍运用齿轮倒棱工艺,降低噪声的工艺方法及应用。
- Finally, the dissertation gave a modification method to cycloidal tooth profile, which can change the engaging position and decrease the efficiency. 最后给出了一种针对摆线齿形的修形方法,通过此种修形可以根据需要改变摆线针轮的啮合位置,适当降低效率,从而改善座椅调角器自锁性能。
- Meanwhile obtained the tooth profile equation of pin-track by the tooth profile normal law which matched the inviolate-cycloid compound gear. 同时利用齿廓法线法得出与该复合齿轮相配套的销轨齿廓方程。
- The tooth profile of this kind of gear was composed of two stepped involutes and a joining trasitional curve between them and formed a ladder shape. 这种齿轮的齿廓由两级渐开线和连接它们的过渡曲线组成,形成阶梯形。
- This paper investigated the tooth profile determination, parameterselection and structure design of hobs for machining arc planet aears. gears. 探讨了加工圆弧行星轮滚刀的齿形确定、参数选择及结构设计。
- In order to avoid the “midconvex” of tooth profile and the serious abrasion in dedendum, the technology of center distance variation was adopted. 为了避免出现齿面“中凸”及齿根部研磨较严重的现象，采用了变中心距研齿工艺。
- According to the curves and equations of the speed, acceleration and displacement about the pallet car given in this paper, the actual tooth profile equation had been presented. 根据台车进行变加速运动的速度、加速度和位移曲线，推导出了实际齿廓方程。
- Terauchi, Y., Nagamura, k., Saijo, H., “On surface durability of Involute-cycloid Composite Tooth Profile Gear”,Bulletin of the JSME, Vol.25,No.202. pp.687-695,1982. 罗文国，渐开线直齿锥形齿轮齿根应力计算模式之初步研究，国立中央大学机械工程学系，2005。
- Regarding isometric curve of two-stub hypocycloid as tooth profile curve of rigid wheel, a harmonic chain drive experimental unit is designed and manufactured. 摘要以双支短幅内摆线的等距曲线作为刚轮的齿廓曲线，设计制作了1台谐波传动试验样机，通过试验验证了谐波链传动的运动可行性；
- Results: Tooth profile in Chinese was significantly different from that of Caucasian but was similar to that of Japanese.Conclusion: The orthodontic appliances should be... 结果:中国人正常牙合牙齿形态与白种人有显著的差异,而与日本人大致相似,但也有一定差别。
- Lazebnilk, I. S., “Minimizing tooth profile errors of hobs,” JSME, International Journal, Series C: Soviet Engineering ResearchVol, No. 4, pp. 109-111, 1990. 方宏声，蜗杆蜗轮组之制造分析，国立交通大学博士论文，民国八十五年六月。
