您要查找的是不是：
- twin screw vessel 双轴船
- This vessel is a trailing suction hopper dredger of steel full welding ,steamline and round-bilge form with twin screw,double rake,single deck,bulb bow and doule tail fin. 本船为双桨、双耙、单甲板、钢质全焊接、流线型、球鼻首、双尾鳍、圆舭型船体的自航耙吸挖泥船。
- Knowledge of General maintenance of twin screw extruder and mixers. 了解搅拌机和双螺杆挤出机的基本维修。
- Two layouts of gear box in twin screw extruders are discussed. 文中介绍了双螺杆挤出机齿轮传动的两种设计方案。
- The corotating twin screw extruders is applied widly on processing of polymer. 同向双螺杆挤出机在聚合物的加工中得到了广泛的应用。
- Six twin screwed steel steam cruisers. 六条双螺纹钢蒸汽巡洋舰。
- A series of silane grafted polyethylenes were prepared by using the twin screw extruder. 以双螺杆挤出机为反应器，制备了一系列硅烷接枝高密度聚乙烯。
- Distributive mixing is achieved in twin screw extruders with narrow kneding block segments. 而分布混合是将熔体分割为条纹，进行均化，增大接触面积。
- A series silane grafted polyethylenes were prepared by using the twin screw extruder. 以双螺杆挤出机为反应器，制备了一系列硅烷接枝聚乙烯。
- Reciprocating Kneading and Extruding System,Clamshell Barrel Co-rotating Twin screw Extruder,PET Washing Line. 往复式单螺杆混炼挤出机，剖分式同向平行双螺杆混炼挤出机，PET瓶片清洗生产线.
- With a windowed twin screw extruder the authors conduct several visualization extrusion experiments. 在可视化双螺杆挤出实验的基础上，阐述了熔融过程中物料运动的多样性问题。
- By comparison, the TATSR has higher efficiency of pumping. plasticization and mixing than that of twin screw reactor. 与双螺杆反应器相比，三螺杆反应器具有较强的物料输送能力、塑化和混合能力；
- This production line adopts single or twin screw extruder as the customers actual production needs. 这条生产线采用单一或双螺杆挤出机作为客户实际生产的需要。
- The mixing facilities have experienced the following steps: Roll mixer,Banbury mixer,Single screw extruder,Twin screw extruder and Twin rotor continuous mixer. 混炼设备的发展经历了下列几个主要阶段:开炼机、密炼机、单(双)螺杆挤出机和双转子连续混炼机。
- Using the datum curves from the twin screw extrusion experiment,the correlative factors influencing the fill ratio of screw are analysed. 利用双螺杆挤出实验中的实验数据曲线，对影响螺杆填充率的诸相关因素进行分析。
- The process of imported twin screw extruder as finishing equipment of adhesive chloroprene rubber(CR 244)was introduced. 介绍了用进口双螺杆挤出机作为粘接型氯丁橡胶(CR244)后处理装置的工艺流程,探讨了其工艺条件及成品橡胶的性能。
- The composite of glass fiber reinforced PET (FRPET)/Ultra-fine CaCO3 modified by La3+ (UCa-CO3-La3 + ) was prepared by twin screw extrusion. 采用双螺杆挤出制备了玻璃纤维增强PET(FRPET)/稀土镧化合物改性超细碳酸钙(UCaC03一La3’)复合材料,将UCaCO3-La3+对FRPET性能的影响与有机钠盐类成核剂NA做了对比。
- The difference between TPU twin screw continuous reactor and conveyer belt production method was indicated and analysized. 比较并分析了热塑性聚氨酯弹性体(TPU)双螺杆法与传送带法生产工艺之间的差别。
- Maleic anhydride(MAH) and styrene(St) melt-grafting onto polypropylene(PP) was conducted in haake torque rheometer and twin screw extruder. 在哈克流变仪和双螺杆挤出机对苯乙烯(St)/马来酸酐(MAH)/聚丙烯(PP)熔融接枝进行了研究。
- The melt grafting of itaconic acid (IA) onto low-density polyethylene (LDPE) was initiated by dicumyl peroxide (DCP) in a twin screw extruder. 以过氧化二异丙苯(DCP)为引发剂,在双螺杆挤出机中制备了衣康酸(IA)熔融接枝低密度聚乙烯(LDPE)。
