您要查找的是不是:
- Fine grain size for the smaller contact area. 接触面积小时用细的粒度。
- Hard grade for the smaller contact area. 接触面积小时用硬的结合度。
- Soft grade for the larger contact area. 接触面积大时用软的结合度。
- Coarse grain size for the larger contact area. 接触面积大时用粗的粒度。
- The contact area between clamp and terminal is either silver or copper. 夹头和电极之间的接触面是银的或铜的。
- The tooth contact and kinematic precision of the modified worm gearing with manufacturing errors has been investigated by the TCA method. 用齿面接触分析法求解了存在制造误差时修形传动的齿面接触状态和运动精度。
- A tooth contact analysis model with a rotating freedom was developed by coupling freedom method to determine the stress and strain field of gears. 摘要利用自由度耦合方法建立了县有旋转自由度的齿轮接触模型,用以分析齿轮的应力应变场。
- Squat and minimize the contact area with the ground as far as possible. 应该蹲著并尽量减少与地面接触的面积。
- The computational models for tooth contact analysis (TCA) and loaded tooth contact analysis (LTCA) of the face gears were established. 建立了直齿面齿轮副轮齿接触分析(TCA)和承载接触分析(LTCA)的计算模型。
- When paged, subjects completed a brief questionnaire containing rating scales of jaw pain, masticatory muscle tension, time and intensity of tooth contact, mood and stress level. 记录时,参与者要完成一份简短的问卷,包括下颌疼痛等级、咀嚼肌紧张度、牙齿接触的时间和强度、情绪和压力水平。
- On the basis of the first envelope ,the paper stresses on the tooth contact analysis of the second envelope,and the equations of a worm and a wormwheel flanks are derived . 本文在第一次包络的基础上,着重进行了二次包络齿面接触分析,推导出了蜗杆和蜗轮齿面方程。
- Slowly pull the assembly outward to open check allowing exposure of the seat and clapper contact area for cleaning. 慢慢将止回阀往外拉,打开止回阀,使得阀座和阀瓣接触面暴露出来便于清洗。
- Check ring gear and pinion gear teeth contact pattern. 检查环形齿轮齿接触印痕。
- The new concepts of flatness, contact area rate, dot distribution and so on are defined. 本文中对适印织物定义了平滑度、接触面积比、网点分配数等新概念 ;
- The contact area between the fluoroalkylsilane film and liquid is small with the effect of the-CF3 group. 并用接触角测定仪三甲基氯硅烷和氢氟硅酸在不同摩尔配比下薄膜疏水性能。
- Based on the coordinate transformation method and gearing theory, the mathematical models for generating the rack cutter, pinion, face-gear, as well as Tooth Contact Analysis (TCA), are established. 应用座标转换法与齿轮啮合原理,本文已导出创成齿条齿面数学模式、小齿轮齿面数学模式、面齿轮齿面数学模式、齿面接触分析数学模式及控制抛物线运动误差大小之统御方程组。
- The deformation on the flexible structure of contact area presented in this paper was analyzed using FEM. 采用有限元法对本研究提出的柔性接触结构进行接触变形分析;
- To increase the contact area and permit larger loads to be carried, the balls run in curvilinear grooves in the rings. 为了增加接触面积并承受较大载荷,滚珠在内外环的曲线槽内滚动。三、译成叠词形式。
- The flexible structure of contact area can reduce the relative slippage between the stator and the rotor effectively. 本研究提出的柔性接触结构能有效减少定、转子间的相对滑动。
- Whichever method is used, and finally the need to brake drum brake shoe and the contact area for more than 70%. 无论采用哪种方法,最后必须使制动鼓与制动蹄的接触面积达到70%25以上。