您要查找的是不是：
- Taian Wuzhou Oil Pump And Oil Nozzle Co., Ltd. 泰安五洲油泵油嘴有限公司。
- Excavation for fuel oil pump house is in progress. 燃油泵房开挖工作正在进行。
- Activates the auxiliary oil pump. 辅助油泵激活按钮。
- Consists of three 55L accumulators, providing assistant driving force for hydraulic system, to perform load and unload of oil pump. 由三只55L蓄能器组成，为液压系统提供辅助动力，实现油泵的承载、卸载运行。
- Having three lobes, as certain leaves. 具三裂片的有三个裂片的，如某些叶子
- Technique advantages of full-lining partial emission slurry oil pump are presented by comparison and analysis to three kinds of slurry oil pump. 通过时三种类型的油浆泵的比较分析，阐述了全衬里部分流型油浆泵的技术优势。
- Stop the running of one oil pump of the electric motor. 停止电机一油泵的运转。
- We are looking for supplier of oil pump PARTS brand name CTR. 我们需要求购汽车机油泵，请联系我们。
- The pressure of lube oil pump increases very slowly. 机油泵压力增长很慢。
- Why You Select LONGTECH New Three Lobes Roots Blower? 为何选择龙铁三叶鲁氏鼓风机?
- You can tell this is the right lung because there are three lobes. 我们能判断出这是右肺因为右肺有三个肺叶。
- Automatic oil pump and fault alarm syster, dygnosis and instructions. 自动注油,自动故障报警、诊断,指导处理。
- BEIJING CITY GUOXING AUTOMOBILE OIL PUMP FACTORY MANUFACTURING CO., LTD. 北京市国兴汽车油泵制造有限公司。
- Exhibits: Forging, brake disc, DrivingShaft, engine, oil pump, Steering Gear. 展品锻件、制动系统、传动轴、水泵、机油泵、转向器。
- Three stage-takedown reconstructions are made to the oil pumps in Xongxian Station so as to improve pump efficiency and cut down power consumption. 为提高泵压的利用率,减少耗电量,对任京线雄县泵站的输油泵先后进行了三次拆级改造,并安装了一台小功率输油泵,以实现输油泵的经济运行。
- Main products: oil tank, oil tube, oiler support, oil pump, oil applying wheel etc. 产品主要结构：油箱、油管、安装支架、油泵总成及涂油轮等组成。
- This paper proposes a design project of the dynamoelectric accelerograph control system of X-aeroengine oil pump modulator. 提出了一种某航空发动机油泵调节器电动油门控制系统的设计方案。
- Profile Design of Wide Double Wedge Involute Rotor for Three Lobe Roots Blower 三叶罗茨鼓风机宽凸台渐开线叶型设计
- The rubber formulation of oil pump bushing was designed by orthogonal testing method design for on NBR(N - 41 ). 选用丁腈橡胶（N-41）为基础胶，利用正交试验法设计出抽油泵衬套橡胶配方。
- The oil pump should be close to the oil tank as possible as it can, the suction height should be no more than 500mm. 油泵应尽量接近油箱,吸入高度不得大于500毫米。
