您要查找的是不是:
- Structural adhesives - Characterisation of a surface by measuring adhesion by means of the three point bending method 建筑用粘接剂。用三点弯曲法测量粘接剂表面的表示特性
- three point bending method 3点弯曲法
- asphalt pavements, crack initiation mechanism, propagation behavior, linear elastic fracture mechanics, collapsed singular isoparametric element, three point bending method, finite element simulation. 01沥青路面,裂纹形成机理,扩展行为,线弹性断裂力学,奇异等参单元,三点弯曲法,有限元模拟
- The material mechanical properties, such as flexural strength, are measured by three point bending techniques. 利用三点弯曲方法测定了材料的抗弯强度等力学性能。
- The effect of specimen size on the J_(Ic) and the slope of J_R curve (dJ/da) was studied by using three point bending (TPB)and side-grooved TPB specimens of different sizes. 本文应用不同尺寸的三点弯曲试样和带边侧槽试样,用实验方法研究了启裂J积分(J_(1C))和J_R阻力曲线的斜率(dJ/da)受试样尺寸的影响。
- By using elasto-plastic finite element calculation and three point bending test,the in-fluence of strength matching and crack depth on fracture properties are investigated. 利用弹塑性有限元计算和三点弯曲试验对不同裂纹深度、不同强度组配焊接接头试样的断裂性能进行了研究。
- According to Chinese Standard GB2038, ?J? integral test was carried out on base metal, weld and HAZ(heat affected zone) of X52 ERW pipes and X60 SSAW pipes under a series of temperature with TPB(three point bending) specimens. 试验按照GB2 0 38标准要求 ,采用三点弯曲试样 ,分别对进口X52ERW焊管母材、焊缝以及国产X60SSAW焊管母材、焊缝、热影响区进行系列温度J积分试验。
- In this paper, a simple formula is derived for calculating the dynamic stress intensity factor (DSIF)of three point bending specimen using dynamic crack opening displacement (DCOD). 给出了一种由裂纹的动态张开位移计算三点弯曲试样的动态应力强度因子的简单方法。
- The results show that,in the mechanical bend fatigue test and three point bend test,the underfill material of U1 and U2 both can improve the mechanical bend reliability of BGA assemblies,and U1 material performs better. 结果发现在机械弯曲可靠性试验中,U1、U2材料的填充均能提高焊点的机械弯曲可靠性,并且U1的效果更好。
- Two series of fatigue crack growth rate (FCGR) tests using three point bend specimen with different integral knife edge designs are performed. Effect of elastic modulus on the measurement of fatigue crack length using compliance technique is analyzed. 用不同整体刀口设计的三点弯曲SE(B)试样做了两组疲劳裂纹扩展速率 (FCGR)试验 ,分析了弹性模量在柔度法测量疲劳裂纹长度中的影响。
- Analysis of the Effect of the Three Point Bending Test of Steel Slabs With Different Coating Using MCA Method 用MCA方法研究不同涂层对钢板三点弯曲的影响
- Test Method for Measuring the Dynamic Mechanical Properties of Plastics Using Three Point Bending 用三点弯曲法测量塑料动态力学性能的试验方法
- Keywords CFRC;age;strength;water ratio;three point bending beam; 碳纤维混凝土;龄期;强度;含水量;三点弯曲梁;
- Test Method for Determination of the Modulus of Elasticity for Rigid and Semi-Rigid Plastic Specimens by Controlled Rate of Loading Using Three Point Bending 用三点弯曲法测定在装载控制速度下刚性和半刚性塑料样品的弹性模量的试验方法
- K_1 of a V-notched Beam under Arbitrary Span Three Points Bending V形切口任意跨距三点弯曲时的K_1
- The Double-K Fracture Parameter of Concrete for Non-Standard Three Point Bending Beam Specimens 砼非标准三点弯曲梁试件双K断裂参数
- Compliance Calibration and Application of SIF of Three Point Bending Specimens with Chevron-Notched 山形切口三点弯曲试样的SIF柔度标定及应用
- It is about three point two meters in height. 这里净高约三点二米。
- Three point support of the best kind. 采用最稳定的三点式支承系统。
- The advantage of branch bending method was while pruning new shoots of main branch could lower fruit set and facilitate guava orchard management. 而屈株法整枝于主干之新梢上,著果可维持较低部位,操作管理方便。