您要查找的是不是：
- A numerical investigation of the effect of particle clustering and thermal residual strain on the micro-mechanical properties of metal matrix composites 颗粒簇增强金属基复合材料的细观力学行为
- thermal residual strain 热残余应变
- Both the alloy composition and residual strain in the grains were determined from the Raman shift. 这两者可借由拉曼频谱来决定晶粒中合金的组合成份以及残留的应力。
- The residual strain is the additional shear strain created with the increase of pore pressure due to cyclic shear under initial shear stress. 残余应变是由于周期剪切引起孔隙压力增长;在初始剪力作用下产生的附加的剪应变.
- An analytical method is presented that predicts the interface debonding length in creamic composites with loading and thermal residual stresses. 提出了陶瓷基复合材料在外载及残余热应力作用下，界面脱粘长度的计算方法。
- The residual deformation around the hole was measured by digital speckle correlation technique and the relation curves of residual strain at the side of hole vs fatigue life cycles were obtained. 再应用数字散斑相关技术测量了不同疲劳循环次数后孔周的残余变形场，并给出了孔边最大残余应变与疲劳循环次数的关系曲线。
- Cracks are formed at the interfaces of Al 2O 3/graphite and TiC/graphite as a result of the action of the thermal residual stress. However no obvious chemical reactions can be observed near the interfaces. 由于热残余应力的作用 ,在氧化铝 /石墨和碳化钛 /石墨界面上有裂纹形成 ,但界面附近没有观察到明显的化学反应。
- Considering the influence of stamping forming to the thickness and residual strain of parts,the thickness distribution and residual strain can gain through the stamping forming calculation. 考虑到冲压成型对零件厚度和残余应变的影响,通过冲压成型计算得到零件在冲压过程中的厚度分布和残余应变。
- Prediction for fatigue life of A3 steel plate with a central hole using critical residual strains criterion, the results were acceptable. 采用临界残余应变判据预测了A3钢构件的疲劳寿命，预测结果是可以接受的。
- P.Z.Chang and C.L.Dai, “Microstructural Fabrication for Measuring Residual Strains of CMOS Thin Films,” Int.Journal Japan Soc.Prec.Eng., vol. 33, No. 2, pp.135 - 140, 1999. 戴庆良;“以标准积体电路制程技术制作微机电感测器之研究”;台湾大学机械工程研究所博士论文(1997).
- THERMAL RESIDUAL STRESS IN AS SQUEEZE CAST SiCw/Al COMPOSITE 压铸态SiCw/Al复合材料中的热残余应力
- Study of residual strain in heavily boron-doped silicon cantilever 单晶硅浓硼掺杂悬臂梁中残余应力的研究
- Keywords thermal residual stress;warpage;injection molding; 热残余应力;翘曲;注塑件;
- Study of residual strain of concrete under fatigue loading 混凝土疲劳残余应变性能研究
- radial distribution of internal longitudinal residual strain 内部轴向残余应变径向分布
- Standard Test Method D 4093-95 for Photoelastic Measurement of Birefringence and Residual Strains in Transparent or Translucent Plastic Materials, West Conshohocken, PA, ASTM, 1995. 标准测试方法d 4093-95为光弹测量双折射和残余株，在透明或半透明的塑胶物料，西conshohocken ，坝，美国ASTM ， 1995 。
- A term sometimes applied to a stylus in a thermal matrix printer. 有时用来指热敏点阵打印机的触针的一个术语。
- NUMERICAL CALCULATION OF THERMAL RESIDUAL STRESS OF INJECTION MOLDED PARTS 注塑件残余热应力的数值计算
- Application Of Mathematical Model To Analyzing Thermal Residual Stresses In Ceramic Coating Material 数学建模在陶瓷涂层材料热残余应力分析的应用
- Thermal Residual Stresses in Aligned Short Fiber Reinforced Metal Matrix Composites 单向短纤维复合材料中热残余应力研究
