您要查找的是不是：
- the deformation of folds 褶皱变形
- Sketch the deformation of the frame corresponding to each. 画出每一种情况下的钢架变形草图。
- Thus we can better understand the deformation of chert in a highly fluid form. 这样我们就能更好地理解燧石在高度流体状态时的变形情况。
- Humility is the ornament of angels and the deformity of devils. 日光之下难事之一就是让自己变得不算甚么。
- She appeared to deformation of the face. 她出现了能变形的面孔。
- We need to consider the deformation of only one strip parallel to generatrix of the cylinder. 我们只需要考虑一个平行于圆柱母线的窄条的变形。
- The deformation of cone-box shaped part in hydromechanical deep drawing is simulated by the FEM software ANSYS. 摘要利用大型有限元分析软件ANSYS对锥盒形件充液拉深的成形过程进行了数值模拟。
- In general, the deformation of the model grille is a combination of axial and shear strains. 一般情况下，模型栅格的变形是轴向应变和切向应变的组合。
- The deformation of a solid body is proportional to the force acting on it , if the force does not exceed a certain limit . 如果作用于某物体的力不超过一定限度的话，则该固体受力后的形变与这一作用力大小成比例。
- Therefore, the calculating method for the bearing capac ity and the deformation of underpinning structure were derived. 并建立了新旧混凝土交接面承载力的计算公式 ;进而提出了桩梁式托换结构承载力和变形的计算方法 .
- The Deformation of thin wall tube in the process of multitool machining is analyzed by using ANSYS software. 应用有限元软件ANSYS对薄壁筒件多刀切削加工进行了变形分析,并从提高工艺刚度的角度出发,提出了相应的工艺措施。
- Hence, it is urgent to study the deformation of screw distributing die widespread plate. 并建立与之相对应的上下模板的三维模型,把狭缝区流场压力作为载荷作用于机头模板上,来研究机头模板的变形。
- The deformation of dam is a three-dimension value including horizontal and vertical displacement. 水坝变形是包括水平位移和垂直位移的三维量。
- The act or an instance of folding. 折叠折叠的动作或事例
- The deformation of deep excavation supported by soil nail is unsuitable to strict requirement of deep excavation. 摘要土钉支护对基坑变形的调节和控制能力较差，不适于对变形控制要求较严格的深基坑工程。
- As the deformation of steels increases from 23% to 76% the processes of recovery and recrystallization are accelerated. 在其它条件给定时,经76%25面缩率拉拔后的钢与23%25面缩率拉拔后的钢相比,前者的回复及再结晶过程加快;
- He paused in the middle of folding up his easel. 他画架收到一半，却停了下来。
- A new type of tube expended fixture was designed , the deformation of the tube plate was simulated by FEM . 设计了新型通用辘管工装夹具,并用有限元法模拟了管板变形的应力状况。
- The results of an example show the validity of the method for simulating the deformation of an opening. 给出了一个含非连续面的洞室开挖问题的算例，计算结果表明了该方法的有效性。
- Then firefighters quickly brought the deformation of the cutting machine for cutting the door. 随后消防队员快速拿来切割机对变形车门进行切割。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries
