您要查找的是不是：
- Is a wedge test specimen utilized for chill or analysis control? 是否用楔型试块进行分析控制?
- The finite element model of a small punch test specimen of 1Cr0.5Mo steel is established. 基于小冲孔蠕变试验 ;建立 1Cr0 .;5Mo耐热钢小冲孔蠕变试样的有限元模型。
- The spectr al reflectance of each test specimen is measured in situ before and after exp osures. 在辐照前后对每一个试样的光谱反射系数进行了原位测量。
- The test specimen shall be immersed in the measuring electrolyte so that the top edge of the area to be measured is level with the surface. 测试样本应浸在电解液中,并使测量区的顶端与液面持平。
- The test specimen may be titrated with the Reagent directly, or the analysis may be carried out by a residual titration procedure. 待测样品可能会被卡尔试剂直接滴定，或者采用回滴定法完成分析。
- Although only then several millimeters are long, but each test specimen includes several thousands has not grown the complete egg. 虽然只有几毫米长，但每个试样含有数千未发育完全卵子。
- Report the viscometer model and spindle, the apparent viscosity at the spindle/speed used, and the test specimen temperature. 记录粘度和锭子，外观的粘度在锭子/和使用的速度，还有测试样品的温度。
- The measuring objectives are selected software controlled in dependence of the test specimen parameters, must be inserted however manually into the mount. 由软件选择样品被测参数,被测物必须用手装入装配台。
- In the second part, a test program to help improve modeling of SCBF systems is described, including the design of a nearly full-size, two-story SCBF test specimen. 在文章的第二部分描述了一个帮助轴心抗拉构件改进建模的实验程序。这部分包括一个接近实际大小的两层轴心抗拉构件的实验范例。
- To produce a pre-determined depth of angle for different impact test specimen material, this device has double thickness gauges and speed adjustor for depth measurement. 简介制作冲击试验机试片之缺口用,本机可调整切口之深度并附良测之设备,本机具切削速度调整可视材料之软硬等状况调整切削速度。
- Used the gold, analysis test method and so on XRD, TEM agglutinates the after test specimen to the vacuum to carry on the microscopic organization analysis. 采用金相、XRD、TEM等分析测试方法对真空烧结后的试样进行了微观组织分析。
- The following tests and measurements shall be performed on the same test specimen. 以下测试和测量应在同一样本上进行。
- The tensile strength shall be determined by applying tension force on the test specimen until it breaks. If the specimen breaks near the cramping position, the test shall be repeated. 测定断裂时的拉力,但在夹持处破裂时要重新试验。
- By use of the method of welding thermal simulation, the morphology in HAZ was simulated and the post-weld heat treatment under different tempering parameter to the test specimen was carried out. 采用焊接热模拟的方法,模拟HAZ粗晶区组织,并在不同回火参数下对试样进行焊后热处理。
- The representative volume of colluvial deposit is larger tha n normal sized testing specimen. 然因崩积层不易取样以及取样后之代表性不足，造成崩积层工程特性研究之困难。
- A simple test will show if this is real gold. 简单的试验就能证明这是否是真金。
- The specimens can drip flaming particles that ignite the dry absorbent surgical cotton located 300 mm below the test specimen. 试片滴落的火焰分子会有短暂的燃烧,且会点燃300mm之下的乾燥的吸收性外科用棉花层。
- The specimens may not drip flaming particles that ignite the dry absorbent surgical cotton located 300 mm below the test specimen. 没有任何试片滴落的火焰分子会点燃300mm下之乾燥的吸收性外科用棉花。
- The test specimens shall be selected at random from shipment of 5000 bricks or less. 试验样品可从5000块左右的待运砖当中任意选出。
- Practice for Design of Molds for Test Specimens of Plastic Molding Materials (08. 塑料模制材料的试样用模型的设计实施规程(08。
