您要查找的是不是：
- Fixed function for routine test mode. 常规试验模式固化功能.
- Under test mode, you run each step individually. 在测试模式下,可以单独运行每个步骤。
- Press the Esc key or close the dialog box to end test mode. 按Esc键或关闭对话框以结束测试模式。
- Using Bluetooth Test Mode for Transmitter Test and Physical level Observe. 蓝牙测试模式实现及其物理层观测。
- TEST MODE: The solenoid is energized with a fixed duration pulsSubsequent fixed pulses occur when the diaphragm reaches the switch closure point. 测试模式:用一个固定的持续脉冲激活电磁阀。当横膈膜达到开关关闭点时，随后出现固定脉冲。
- No matter how the dialog box will behave at run time, you can terminate it in test mode by pressing ESC. 不论对话框在运行时的行为如何,您都可以通过按Esc键在测试模式下终止它。
- If you want to run the step for testing, you must promote it to test mode. 如果需要运行这一步骤来执行测试,则必须将该步骤升级到测试模式。
- When you promote the step to test mode, the Data Warehouse Center creates the target table. 当您将这一步骤升级到测试模式时,Data Warehouse Center就会创建目标表。
- Capable of operating various machine tools, can read drawings.Loading mode.With mold, to an independent test mode. 能操作各种加工机床，能看懂图纸.;装模
- Therefore, after you promote a step to test mode, you can make only those changes that are not destructive to the target table. 因此,当您将一个步骤升级到测试模式之后,就只能进行那些不会损坏目标表的修改。
- The Functional Test Mode was also selected so that the full IFX-encoded response was captured in the test results managed by the. 管理的测试结果中捕获完整的IFX编码的响应。
- You can change the properties of a replication step in test mode, and the changes will be valid as long as the replication step is not demoted to development mode. 可以修改测试模式中复制步骤的属性,只要不将复制降级到开发模式,修改就会有效。
- In this paper, the test mode on sphericity deviation measurement by three-coordinates measuring machine and the conclusion from measurement results are given. 本文给出了在三坐标机上测量钢球球度误差的测试方法及对测试结果的分析。
- Capable of operating various machine tools, can read drawings.Loading mode.With mold, to an independent test mode, test mode to analyze and resolve the situation. 能操作各种加工机床，能看懂图纸.;装模
- A simple test will show if this is real gold. 简单的试验就能证明这是否是真金。
- Testing Mode: Time of power on or off, and testing time are set by the touch screen, and test circularly by PLC. 测试方式：通电、断电时间，测试次数由触摸屏设置，并由PLC自动循环测试。
- It uses an errorless learning method and have drill and test modes, which the user can set. 本软件练习使用无误差的学习方法，并且分练习篇及测试篇供用者自行设定。
- Adopting the four pins of TAP:Test Data In,Test Data Out,Test Clock,Test Mode Select of TM1300 and the experiment realized the hardware connection with EPP of PC through CPLD,electric level match. 采用TM1300的测试访问端口控制器TAP中的Test DataIn;Test Data Out;Test Clock和Test Mode Select4个信号管脚;通过CPLD和电平匹配;实现了与PC机增强型并口协议并口的硬件连接.
- Pupils who pass the test will be promoted to the next higher grade. 小学生只要考试及格就会升到高年级。
- Laser reconnaissance and warning radiation lab simulation test mode in laser extinctive chamber is analyzed.A simulation test project using laser designating simulator is proposed. 摘要研究了利用激光暗室进行的激光侦察告警辐射式仿真测试模式，提出利用激光指示信号模拟装置的仿真测试方案。
