您要查找的是不是：
- All needle valves must be closed on test kit. 检测组件上的所有针形阀必须关闭。
- Check the acidity of the soil with a test kit. 用试验器具测一下土壤的酸度。
- For digital printout model test kit, request F-TK-DL. 适用于数字打印输出型号的检测组件，请参阅F-TK-DL.
- Before starting test, all needle valves on test kit must be closed. 在开始检测前,检测组件上的所有针形阀都必须关闭。
- Checking the mud test equipment in the pilot test kit. 检查仪器箱中的泥浆试验设备。
- Turn test kit on, wait until self check is complete. 打开检测组件,等到自测完成为止。
- Open test cock No. 1 and bleed valve "A" on top of test kit. 开启测试旋塞1号和检测组件顶部上的排气阀“A”。
- Open bleed valve "A" on top of test kit and bleed air from hose. 开启检测组件顶部的排气阀“A”，并且从软管排放空气。
- Before starting test, all needle valves on the test kit must be closed. 在开始检测之前,检测组件上的所有针形阀必须关闭。
- The reliable, validated diagnostic test kit for detection of crops is the key! 简便,快速,有效的检测试剂是成为关键!
- Install hose between test cock and connection "A" high side (red) of test kit. 在测试旋塞和检测组件的连接“A”高端（红）之间安装软管。
- ECB can be made of a test kit for detecting the samples containing alcohol. 可实现乙醇的微量化、快速化测定; ECB可制成荧光毛细乙醇测试盒,用于含乙醇样品的测定。
- Open test cock No. 2 and needle valve "A" high side (red) on test kit. 开启测试旋塞2号和检测组件上的针形阀“A”高端（红）。
- Bleed hose and test kit of air, when bleeding hose fill vent with water, shut off VA. 排放软管和检测组件内的空气，在排放软管空气时用水注入排气口，关闭阀门A。
- Caution: To prevent freezing, hold Test Kit vertically to drain differential gauge and hoses prior to placing in case. 警告:为了防止冰冻,在进行安置前,要保持检测组件与排泄差压表和软管垂直。
- Note: After test, all valves on test kit must be fully open and hose removed to prevent damage to test kit. 注:检测后,测试组件上的所有阀门都必须出于全开状态,并拆卸所有软管,以防止测试组件损坏。
- Test kit contains: gauge, test valves, hoses, adaptors, securing strap, instruction guide and lightweight case. 检测组件包括:仪表,测试阀,软管,适配器,安全带,说明书和轻便箱盒。
- Open TC #4 and loosen hose at vent needle valve connection bleeding air from test kit. 开启测试旋塞4号，松开排气针形阀上的软管，从检测组件上排放空气。
- Caution: To avoid freeze damage to the test kit it should be stored in a dry warm area when not in use. 警告:为了避免检测组件受到冰冻破坏,在未使用期间,应该存放在干燥温暖的地方。
- Install hose between test cock No. 2 and connection "A" on high side (red) on test kit. 在测试旋塞2号和检测组件高端（红）上的连接“A”之间安装软管。
