您要查找的是不是:
- The results showed that the Vicat softening temperature and the tensile yield strength were improved with the increase of CPVC content. 结果表明,共混材料的维卡软化温度和拉伸屈服强度随CPVC用量的增加而增加;
- The results showed that the Vicat softening temperature and the tensile yield strength were improved with increasement of CPVC content. 结果表明,共混材料的维卡软化温度和拉伸屈服强度随CPVC用量的增加而增加;
- The results showed the Vicat softening temperature,tensile yield strength and melt viscosity of the blend increased with the increase of CPVC content. 结果表明:共混物的维卡软化温度、拉伸屈服强度和熔体粘度随CPVC用量的增加而明显增加;
- Elastic-plastic Bending Induced Residual Stress and Its Influence on Tensile Yield Strength of Plates 弹塑性弯曲所致残余应力及其对板料拉伸屈服强度的影响
- tensile yield strength 受拉屈服强度
- hoop tensile yield strength 环向拉伸屈服强度
- The result show that the yield strength of the bars drop apparently and the tensile strength rise a little. 结果表明,自然时效后钢筋的屈服强度有较大幅度下降,抗拉强度有小幅度的上升。
- Tensile and yield strength are determined by pulling a standardized machined sample in an tensile testing machine until the sample breaks. 抗拉强度和屈服强度的测定是在拉力试验机中将一个加工好的标准试样进行拉伸直至试样断裂。
- The output parameters of the model are three mechanical properties namely ultimate tensile strength (UTS), yield strength (YS) and elongation (ELO). 模型的输出为三个力学性能指标,即抗拉强度、屈服强度和延伸率。
- Compared with the original material, the SMAT Ti's elastic modulus decreased, yield strength and tensile strength increases while elongation decreases. 与SMAT处理前的纯钛相比,处理后材料的弹性模量下降,屈服强度和抗拉强度提高而塑性下降。
- Properties determined by mechanical testing, such as yield strength, ductility, ultimate tensile strength, hardness, bendability, impact strength, etc. 由机械试验决定的特性,如屈服强度、延展度、极限抗张强度、硬度、弯曲性、冲击强度等。
- After controlled above process parameters, tensile strength, yield strength, elongation and microstructure were investigated to verify the real automobile applicability. 在研究了拉力、屈服强度、伸长率和微观结构等工艺参数之后;验证在实际的汽车中的适用性.
- At this condition,the tensile strength,yield strength,elongation and electric conductivity of studied alloy are 595.8 MPa,572.0 MPa,8.3% and 38.45%IACS respectively. 经RRA处理;其抗拉强度为595.;8MPa;屈服强度为572
- At this condition,the tensile strength,yield strength,elongation and relative electrical conductivity of the tested alloy is 545.9MPa,438.9MPa,19.2% and 46.7%IACS,respectively. 在最佳固溶时效处理条件下 ,合金的抗拉强度、屈服强度、伸长率和相对电导率分别为5 45 9MPa、4 38 9MPa、19 2%25和 4 6 7%25IACS。
- The influence of thermal oxygen on the tensile yield stress, tensile breaking stress, impact strength, elongation at break , melt point and the heat of melting of PF Nylon 1212 is investigated. 通过热氧老化试验,考察了热氧对尼龙1212拉伸屈服应力、拉伸断裂应力、冲击强度、断裂伸长率、熔点、熔融热的影响。
- The tensile strength,yield strength and notch toughness of Q420 angle steel produced by V-N interalloying method were improved evidently and integration properties were better. 采用加入V-N中间合金方法生产的Q420角钢的抗拉强度、屈服强度和冲击韧性明显提高,具有较好的综合性能。
- The results show that the influences of the glass beads content and its diameter on the tensile yield stress and strain at yield are not significant. 结果显示,微珠含量及其直径对复合物的拉伸屈服应力和屈服发生时的应变影响不太明显。
- After controlled aboe process parameters, tensile strength, yield strength, elongation and microstructure were inestigated to erify the real automobile applicability. 在控制了以上的工艺参数后,也研究了抗张强度、屈服强度、伸长率和微观结构以验证在真车中的适应性。
- The tensile yield stress and flexural stress are much higher in the composites containing compatibilizer than the composites with coupling agent treated CaCo3. 另外,也将相容剂法与传统的偶联剂法进行了比较。
- Desirable properties for forming include low yield strength and high ductility. 令人满意的成形特性包含了低降伏应力和高延展性。