您要查找的是不是：
- surface compressive stress 表面压应力
- By improving and optimizing some parameters of shot peening technology,we can acquire desired residual compressive stress and its depth below surface. 通过控制喷丸工艺参数，寻求理想的残余压应力值和残余压应力层深度。
- The laser shock processing causes the surface layer of metal to plastically deform,and thereby develop a significant residual compressive stress in the surface of metal. 激光冲击处理会使金属材料表层发生塑性变形而产生很高的残余压应力;
- Due to even compressive stress on toughened glass surface, and the corresponding tensile stress in inner layer,toughened galass is a sort of high strength safety glass. 钢化玻璃表面形成均匀的压应力，内层呈现相应的张应力，所以钢化玻璃是一种高强度的安全玻璃。
- When the fill factor is less than 1, the concentrated tensile stress appeares near edge of disk surface, while the fill factor reaches up to 1, the surface exhibites compressive stress, and the center is less tensile stress. 当抽运光斑未充满激光介质时，介质的表面靠近边缘处会出现大的拉应力集中，并且介质表面的最大轴向位移和最大拉应力随光斑填充因子增大而增大；而当抽运光充满介质时，表面是压应力，较小的拉应力存在于介质内部。
- It was discovered that a residual compressive stress is produced on the work-piece surface through lapping, the residual stress increased with abrasives size, lapping pressure and lapping speed. 发现了固着磨料研磨使工件表面产生的残余应力为压应力。当磨料尺寸增大、研磨速度提高时,残余应力增大。
- However, anterior and posterior joint surfaces of the subtalar joint sustained compressive stress, and medium joint surface of subtalar joint received tensile stress. 而距下关节于足跟著地期，前与后关节面承受压力，中关节面则承受张力。
- The compressive stress of general polyamine soft foam plastic is improved with polymer polybasic alcohol . 为了改善普通聚氨酯软泡的压陷性能,采用添加聚合物多元醇,并对照其添加前后的物性。
- Compressive stress is transferred by carrying plate and PBL (Perfo-Bond Leisten) shear connectors. 压应力由承压板及PBL剪力键共同传递，拉应力、剪应力主要由PBL，剪力键传递。
- The coating is of a compressive stress and the base metal is of a tensive stress. 计算结果表明,由于瓷层与金属基体热膨胀系数存在差异,瓷层处于压应力状态,金属基体处于拉应力状态;
- As the radium of pipe increases, the absolute value of the radial stress decreases, and the compressive stress o... 随着管道半径的增大,径向应力绝对值减小,瓷层所受的压应力也减小。
- Earlier stage was NS compressive stress and thereafter EW compressive stress,later stage NS torsion stress. 先期为南北向的挤压应力,其后是东西向的挤压应力作用,后期为南北向的扭动应力作用。
- An applied tensile or compressive stress resolved into a shear component along a specific plane and direction within that plane. 一个实际拉或压应力沿某一特定平面和在该平面特定方向上分解得到的切应力分量。
- Objective To investigate the effect of different diameter powder on setting time and compressive stress of carbonated hydroxyapatite cement (CHC). 目的 检测不同粉体粒径对碳酸化羟基磷灰石水泥 (carbonatedhydroxyapatitecement,CHC)的固化时间和压缩强度的影响 ,为其修复骨缺损提供理论基础。
- The results show that the orientations of principal compressive stress and principal tensile stress are NEE and NNW respectively. 结果表明：主压应力为北东东向，主张应力为北北西向；
- The maximum draw stress located on the lingual apex, while the maximum compressive stress located on the lingual crest of the ridge. 最大拉应力位于舌侧根尖部，最大压应力位于舌侧牙槽嵴顶。
- The growth behavior of short through-thickness crack in the residual compressive stress which was introduced by a pressin method was investigated. 摘要用压入法引入残余压应力，以研究穿透短裂纹在残余压应力中的扩展规律。
- In the paper tape business card printing and membership card making, paper tape from a rubber sleeve surface compression area, and then gradually into the drawing area. 在纸带制卡和会员卡制作过程中，纸带是从橡胶套筒表面压缩区域进入的，然后逐渐进入拉伸区域。
- The shift of G peak position toward lower wavenumber is because of the releasing of compressive stress in a-C:Cu films by the addition of Cu. 实验结果显示随著铜含量增加，发现粗糙度提高并且表面尖锥数量增加及细化的现象，但铜在膜中分布均匀。
- Under axial force, moment and shear force steel-concrete joint subjected to compressive stress, tensile stress and shear stress. 在轴力、弯矩和剪力的作用下，钢-混凝土接头处将产生轴向压应力、拉应力和剪应力。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries
