您要查找的是不是:
- steering knuckle spindle 转向节上的轮毂轴,转向关节枢
- Wheel shaft, wheel rim, gear, gear ring, con-rod, crankshaft, steering knuckle, steering arm, cam flange, spindle etc. 轮轴、轮毂、齿轮、齿圈、连杆、曲轴、转向节、转向节臂、垂臂;突缘、十字轴等异形件;轴类零件等锻件及主、被动齿轮成品。
- Remove the steering knuckle from the strut. 自支柱拆除转向关节。
- Route sensor wire from steering knuckle to fender panel. 从转向节到防护板安排感知器导线走向。
- This movement is produced by gearing and linkage between the steering wheel in front of the driver and the steering knuckle (or wheel). 这一运动是由装在驾驶员前面的转向盘与转向节(车轮)之间的转向器和连杆装置来共同完成的。
- Based on the analyses, the forging process for a steering knuckle has been designed. 在此基础上,进行转向节锻造设计。
- The results show that the thermomechanical treatment can improve the quality of the automobile steering knuckle. 结果表明,锻造余热淬火工艺对汽车转向节质量有明显改善。
- The hub and bearing assembly does not require removal from the steering knuckle to replace wheel attaching studs in the hub and bearing assembly. 更换轮毂及轴承组件内的车轮固定螺桩无需自转向关节中取出轮毂及轴承组件。
- "The steering knuckle then supported through Ball joints, by upper and lower control arms which are attached to the car frame. 转向节通过球头节与安装在车架上的上下控制臂相连。
- Macro and micro structure of the fractured steering knuckle arm was examined by optical microscope and scanning electron microscope. 采用光学显微镜和扫描电镜对断裂转向节臂的宏、微观组织进行了分析。
- A steering knuckle is the key component in cars, which needs high requirements in dimensional accuracy and product quality. 摘要轿车转向节是轿车上的关键零件,对尺寸精度和产品质量要求很高。
- The effect of thermomechanical treatment on the microstructure and properties of the automobile steering knuckle was researched in this paper. 研究了汽车转向节锻后余热淬火工艺对钢的组织和性能的影响。
- The forming process of 6400 steering knuckle arms was analyzed by plastic FEM software Deform. The reasons causing the problems of fold and underfill in the production were found. 使用塑性有限元分析软件deform对 640 0转向节臂成形过程进行了模拟分析 ,找出了其在生产过程中出现的折叠、缺肉等问题的原因。
- During steering maneuvers, the strut and the steering knuckle (through the ball joint and a pivot bearing in the strut's upper retainer) turn as an assembly. 车辆转向时,支柱以及转向关节(经由球形接头与上支柱固定器之轮毂轴承)会一体旋转。
- It consists of steering wheel, steering shaft, worm, gear sector, pitman arm drag link, steering knuckle arm, king pin, steering arms, tie rod, front axle and steering knuckle. 转向系统包括转向盘、转向轴、蜗杆、扇形齿轮、转向摇臂、直拉杆、转向节臂、主销、转向臂、转向直拉杆、前轴和转向节。
- On single-ended output's gear rack type diverter, a rack's end with changes the steering knuckle tie rod through the inside and outside bracket to be connected. 在单端输出的齿轮齿条式转向器上,齿条的一端通过内外托架与转向横拉杆相连。
- Con-rod for ship building, high pressure forged block for petrolium, front axle, steering knuckle, crankshaft and core shaft for automobile, turbine blade for energy industry. 船舶类:船用柴油机连杆系列石油类:高压锻钢阀体1、2、3、4寸系列汽车类:前轴、转向节、曲轴、芯轴系列能源类:叶片
- Lots of well-forged, normatively heat-treated, and elaborately-processed steering knuckle arms, pitman arm, idler arm pendulum lever etc, can be used widely as parts of various types of truck and car. 众多锻造精良、热处理规范、加工精细的转向节臂、摇臂、随动臂、摆臂等品种,可为载重车、乘用车广泛地提供所需型号的配套件。
- The force applied on front-wheel is discusced through an example in which tractor steering knuckle kingpin is tendency inside, and the returning positive moment acquired by front-wheel ground counteraction is also analysed. 摘要从车辆前轮的受力出发,以拖拉机转向节立轴内倾时为例,分析了前轮接地反力作用所产生的回正力矩。
- By improving the design of forging die and using press-forging and backward extrusion principle,solves the problems of 130 steering knuckle forming which can not be fully filled during forming. 通过改进预锻模膛的设计,利用镦粗成型、反挤成型的原理,有效解决了130转向节板部模锻成型时充不满的问题。