您要查找的是不是：
- Macro and micro structure of the fractured steering knuckle arm was examined by optical microscope and scanning electron microscope. 采用光学显微镜和扫描电镜对断裂转向节臂的宏、微观组织进行了分析。
- It consists of steering wheel, steering shaft, worm, gear sector, pitman arm drag link, steering knuckle arm, king pin, steering arms, tie rod, front axle and steering knuckle. 转向系统包括转向盘、转向轴、蜗杆、扇形齿轮、转向摇臂、直拉杆、转向节臂、主销、转向臂、转向直拉杆、前轴和转向节。
- Fatigue Simulation of Steering Knuckle Arm 汽车转向节臂疲劳仿真
- Lots of well-forged, normatively heat-treated, and elaborately-processed steering knuckle arms, pitman arm, idler arm pendulum lever etc, can be used widely as parts of various types of truck and car. 众多锻造精良、热处理规范、加工精细的转向节臂、摇臂、随动臂、摆臂等品种，可为载重车、乘用车广泛地提供所需型号的配套件。
- The forming process of 6400 steering knuckle arms was analyzed by plastic FEM software Deform. The reasons causing the problems of fold and underfill in the production were found. 使用塑性有限元分析软件deform对 640 0转向节臂成形过程进行了模拟分析 ,找出了其在生产过程中出现的折叠、缺肉等问题的原因。
- Loaded Vibration Test and Simulation for Steering Knuckle Arm 轿车转向节臂振动加载试验与仿真
- Fracture failure analysis of left steering knuckle arm 左转向节臂断裂失效分析
- FRACTURE ANALYSIS OF STEERING KNUCKLE ARM IN A FD2815X TYPE VAN FD2815X型农用车转向节臂断裂分析
- Keywords Steering knuckle arm Fatigue fracture Decarburation; 转向节臂;疲劳断裂;脱碳;
- Forming Analysis And FEM Simulation of 6400 Steering Knuckle Arms 6400转向节臂成形分析及有限元模拟
- steering knuckle arm 转向关节臂,转向节臂
- Remove the steering knuckle from the strut. 自支柱拆除转向关节。
- Wheel shaft, wheel rim, gear, gear ring, con-rod, crankshaft, steering knuckle, steering arm, cam flange, spindle etc. 轮轴、轮毂、齿轮、齿圈、连杆、曲轴、转向节、转向节臂、垂臂；突缘、十字轴等异形件；轴类零件等锻件及主、被动齿轮成品。
- "It consists of steering wheel, steering shaft, worm, gear sector, pitman arm drag link, steering knuckle arm, king pin, steering arms, tie rod, front axle and steering knuckle." 转向系统包括转向盘、转向轴、蜗杆、扇形齿轮、转向摇臂、直拉杆、转向节臂、主销、转向臂、转向直拉杆、前轴和转向节。
- Route sensor wire from steering knuckle to fender panel. 从转向节到防护板安排感知器导线走向。
- This movement is produced by gearing and linkage between the steering wheel in front of the driver and the steering knuckle (or wheel). 这一运动是由装在驾驶员前面的转向盘与转向节(车轮)之间的转向器和连杆装置来共同完成的。
- Based on the analyses, the forging process for a steering knuckle has been designed. 在此基础上，进行转向节锻造设计。
- The results show that the thermomechanical treatment can improve the quality of the automobile steering knuckle. 结果表明,锻造余热淬火工艺对汽车转向节质量有明显改善。
- The hub and bearing assembly does not require removal from the steering knuckle to replace wheel attaching studs in the hub and bearing assembly. 更换轮毂及轴承组件内的车轮固定螺桩无需自转向关节中取出轮毂及轴承组件。
- "The steering knuckle then supported through Ball joints, by upper and lower control arms which are attached to the car frame. 转向节通过球头节与安装在车架上的上下控制臂相连。
