您要查找的是不是:
- The Measurement and Analysis of Stress in the Shaping of the Shell of High-Strength Steel spherical Tank 大瓣片高强钢球壳板冲压成形应力测试与分析
- Application of heating spatter technology in prevention on LPG steel spherical tank 中温碱液储罐防腐涂层技术与应用
- Taking the LGP spherical tank of high strength steel as an ohject. 球形储罐由于不断发生球罐开裂,泄漏事故,影响了球罐发展。
- steel spherical tank 球罐
- 15MnVNR steel spherical tank 15MnVNR钢制球罐
- Impact &fracture toughness properties of steel plate and welding joint of WEL-TEN610CF for natural gas spherical tank were investigated. 对特大型天然气球罐用WEL-TEN610CF钢板与焊接接头的冲击及断裂性能进行了试验研究。
- Discussion about Rule of Diffusible Hydrogen Content in Deposited Metal of High Strength Low Alloy Steel Spherical Tanks 对高强钢球罐用焊条熔敷金属扩散氢含量的测定
- Strength and Deflection Stress Calculations & Evaluation of Centripetal Take Over Oblique Flanges and Component Tube for 1000m 3 LPG Steel Spherical tanks 1000m~3液化石油气球罐向心接管斜法兰强度及配管位移应力计算与评定
- stainless steel spherical tanks 不锈钢球罐
- The spherical tank (gas holder, container) will be shipped in the condition of edge prepared and bent plates. 球罐(气柜、容器)将以板加工和弯板的条件发货。
- The reasons for crack appearance in LPG spherical tank and the methods for prevention. 介绍液化石油气球罐检验中裂纹形成原因及预防措施。
- It is important to assess the complex risk and hazards of fragment of spherical tank BLEVE quantitatively. 本文的研究结果对于定量评价球罐发生BLEVE之后碎片所造成的危险分析具有重要意义。
- The dieless hydro-bulge process of stainless steel spherical shells are numerically simulated by elasto-plastic FEM. 用弹塑性有限元对不锈钢球壳液压胀形过程进行了数值模拟。
- During the process of heat treatment of a large spherical tank, the turbulent combustion will occur inside the spherical tank. 对球罐内部进行燃烧整体热处理时,因密度不均匀,使浮力对其内部流场有直接影响。
- This paper presents the whole body heat treatment process and procedure of ammonia spherical tank and appraises the result of the heat treatment. 介绍建峰化工总厂化肥厂氨球罐的整体热处理工艺和过程,并对热处理效果进行评价。
- In order to reduce possibility of LPG leakage accident, some suggestions were provided for design of LPG pressured tank (spherical tank). 从降低LPG泄露事故发生几率角度出发,针对LPG压力储存系统(球罐)的设计提出几点建议。
- Using the front treatment program of the finite element method, the mechan-ics modeles of spherical tank and cylindrical tank are automatidy shaped on the screen or the plotter. 采用有限元前处理程序,自动生成常见球罐和柱罐的优化力学模型,并在屏幕上或用绘图仪绘制出罐体的三维图形,建立起受压容器开口补强优化设计的数学模型。
- The process of welding and heat treatment for spherical tank in special environment were stated in this article. Some relevant viewpoints and methods were also presented. 本文分析论述了球罐特殊环境(东北沿海地区、冬季施工)中焊接与热处理的有关问题,并提出一些有针对性的见解和做法。
- An improvement in level calculation for spherical tank is putforward aimed at some questions in practice[1].The difference is p resented with comparision. 针对文献[1]球形容器充液高度计算过程中出现的问题,提出改进后的算法方案,并与原方案进行比较分析。
- The necessarily of post-weld heat treatment of spherical tanks was emphasized. 强调了焊接球罐焊后热处理的必要性。