您要查找的是不是：
- Adds a spline curve to the current figure. 向当前图形添加一段样条曲线。
- Fills the interior of a closed cardinal spline curve defined by an array of. 结构数组定义的闭合基数样条曲线的内部。
- A B-spline curve allows local control over the shape of a spline curve. （B样条曲线允许局部控制曲线的形状。）
- A cardinal spline curve is used because the curve travels through each of the points in the array. 由于曲线经过数组中的每个点,因此使用基数样条曲线。
- In this paper, an algorithm for constructing rational spline curve, which was tangent to the given polygon, was described. 摘要描述了一种与给定多边形相切的有理样条曲线的算法。
- Given a set of planar control vertexes, the algorithm can easily construct a G2 cubic a -B?ier spline curve. 这个算法,可以对给定的一组平面控制顶点,方便地构造一条G2三次a-B?ier样条曲线。
- A piece of quartic spline curve was constructed and the same analysis was applied to it as well for comparison. 给出一个拐角重构实例，插补构建的曲线，并分别分析了插补输出的速度、加速度及加加速度。
- The computer calculates the inbetweens values based on a spline curve connecting the keyframe values. 然后计算机基于样条曲线计算出连接关键帧数值的中间画的数值。
- Described an algorithm for constructing trigonometric spline curve, which was tangent to the given polygon. 摘要描述了一种与给定多边形相切的三角样条曲线的算法。
- The paper introduces a new way to calculate the structure of a given woven fabric on the basis of float combination with B spline curve funct. 本文根据浮长线对织物结构影响的原理,结合三次B样条函数,对机织物结构进行计算,根据计算结果可以得到模拟图像效果。
- The local modification to the trigonometric spline curve could be completed by simply adjusting the corresponding control parameters. 所构造的曲线对多边形具有保形性，曲线可以局部修改。
- A new spline curve is presented which interpolates given points and tangent directions with piecewise involute of circle. 利用拼接的圆渐开线实现对平面上的数据点及其切向的插值。
- If the method is combined with the subdivision method of curve,the rational spline curve with higher-order continuity is presented which is the approximation of offset curve. 该方法与离散算法相结合,可得到等距曲线的高阶连续的有理样条逼近曲线,最后,通过数值实例与已有方法作了比较。
- Curvature monotony condition Tor the quadratic rational B spline curves. 二次有理B样条曲线曲率单调条件
- The results indicate that the reconstructed quintic spline curve can ensure the cutter transit well for corner contour, and that the cutting performance is superior to that of the quadratic one. 同时也重构了一条四次样条曲线与五次样条曲线作对比分析，结果表明，五次曲线能使裁刀获得良好的且较四次曲线优越的轮廓拐角加工性能。
- The geometric continuity of cubic a -B?ier curves is discussed, and algorithm of constructing planar G2 cubic a -B?ier spline curves is presented. 对三次曲线的几何连续拼接问题做了研究。 给出了构造平面G2组合三次a-B?ier曲线的几何算法。
- The mean idea is：Fairing of C-B spline curves is fulfilled by adjusting the value of parameterand control points to reduce the implied energy. 该算法的基本思想是：通过调整控制参数和控制顶点使得曲线的能量最小，得到最优的光顺逼近曲线。
- Abstract: A algorithm to reconstruct the corner with quintic spline curves was proposed for improving cutter's motion stability and transition velocity. 摘要为提高裁刀拐角过渡速度及获得良好的运动平稳性，提出五次样条曲线拐角重构算法。
- The sensitivity analysis was developed using the rigid viscoplastic finite element method.The preform die shapes are represented by cubic B spline curves. 表示预锻模具形状的三次B样条曲线的控制系数用作设计变量。
- A Fast Algorithm of Fair Spline Curve 一种光顺样条的快速生成算法
