您要查找的是不是：
- CNC words begin with letter addresses (like F for federate, S for spindle speed, and X, Y, &Z for axis motion). 数控字以字母地址开头(如F表示进给速度，S表示主轴转速，X，Y，Z表示轴运动)。
- Fast 7200 RPM spindle speed and EIDE Ultra ATA 100 for burst transfer rates up to 100 MB s. 快速7200 RPM转轴速度及EIDE Ultra ATA 100令突发传输率高达100 MB秒。
- In this paper, a type of NC lathe's main transmission agent by using a frequency modulation AC Spindle Motor and a tree speed gear box to make the spindle speeds be stepless change was present. 介绍一种以交流变频调速主轴电机驱动、串接一个3档分级变速机构，实现主轴无级变速的数控车床主运动传动系统。
- The test result shows tha the influence of related displacement on surface finish is linear and related to amplitude and frequency of vibration and spindle speed. 试验结果表明：相对位移对表面光洁度的影响是线性”的，不仅与振动幅值有关而且与振动频率及主轴转速有关。
- Use of long separator plates at high spindle speeds. 在高锭速下使用长隔纱板。
- All spinning parameters are computer controlled including draft, count, twist direction, twist level, traverse and spindle speed. 所有纺纱参数由电脑控制，包括：牵伸、支数、捻度方向、捻度水平、往复动程和锭子速度。
- An applicable method to control regenerative cutting chatter automatically based on the optimal regulation of spindle speed is introduced. 提出一种实用的通过主轴转速寻优调整对再生型切削颤振进行自动控制的方法。
- The result of subentry statistic shows that the main influence factors on twist irregularity are spindle speed, input speed of folded yarn and single yarn evenness. 因素分项统计结果表明,锭速、股线输入速度、单纱条干均匀度是影响股线捻度不匀的主要因素。
- The speed change between two gears depends upon the number of teeth on each gear. 两个轮之间速度的改变取决于每个轮上的数目。
- A constant surface seed control was incorporated and continuously anticipated the most efficient spindle speed for the next cut to minimize time lost or spindle acceleration. 一个表面的控制将整合并不断地预测最有效的轴速,一是下一次切割用最少的时间或最小的转速。
- Based on the characterites of hollow spindle spinning principle,the paper introduced the superfeed ratio,wsap twist and spindle speed had influence on fancy effect. 本文在简述空心锭纺纱原理的基础上，研究了超喂比、包缠拈度和纺纱速度对花式纱线花式形态的影响。
- Takamiya, K., Sadao, M. and Inoue, K., "Speed change device for bicycle," U.S.Patent No. 4,838,122, June 1989. 陈弘轩，自行车内变速器系统之电脑辅助设计，国立中山大学机械与机电工程研究所硕士论文，中华民国九十四年六月。
- Subsequently, the influence of different interference, grip length and spindle speed on the grip rigidity of the matching of lengthened shrink-fit holder and cutting tool. 随后对不同过盈量、夹持长度及主轴转速对热缩加长刀杆与刀具配合的径向夹持刚度的影响进行分析。
- The boring power comes from the head-stock of a universal lathe, so the spindle speed could be adjusted in a wide range and satisfactory end face scraping quality is ob-tained. 镗削动力头采用了普通车床的床头箱,主轴转速调节范围大,刮削端面性能良好。
- The structure and size of the ERF stepless speed change device also have influence on output rotational speed. ERF调速装置的结构尺寸也影响输出转速。
- Due to the unreasonable design of the transmitting ratio in the major transmission system of lathe C6143, the progression of the spindle speed is asymmetrically distributed. 在C6143型普通车床主传动系统中,由于传动比设计不够合理,致使主轴转速级数分布不均;
- On the basis, we also developed SZG-A. it can carry out steeples speed change and constant temperature control. 在些基础上，我们开发了SZG-A，它既可无级调速，又能进行恒温控制。
- This paper introduces an assembly method for guaranteeing assembly accuracy of the DBL stepless speed change device. 本文介绍一种保证DBL型无级变速器装配精度的装配方法。
- Have used the key associating one recover being able to make net speed change slow? 您的位置：我也知道>电子数码>用了联想一键恢复会不会使网速变慢？
- Effect of adding comber waste is more than adding soft waste. Close roller settings and very high spindle speeds. 罗拉隔距太小,锭速太高。
