您要查找的是不是：
- With the rise of solution temperature, the thickness of recrystallized layer increase. 再结晶层厚度随固溶温度的升高而增大；
- Relatively small changes in solution temperature or pH, for example, may cause denaturation, which usually occurs without severing covalent bonds. 例如溶解温度或pH值相对很小的变化可能导致变性,这种特性通常不破坏共价键。
- The experiment result is of great importance to guide the management of the nutrient solution temperature under NFT cultivated condition in strawberry. 试验结果对草莓薄层水耕栽培的溶液管理有重要的指导意义。
- The results show that the spectrum intensity of the elements Ba, Cu and Zn increases obviously with increasing the solution temperature. 实验结果表明,随着溶液温度的提高,元素钡、铜和锌的谱线强度有明显的增强。
- Influence of solution temperature and cooling rate on tensile property and microstructure of TC18 alloy has been studied. 本文研究了固溶温度、冷却速度对TC18钛合金拉伸性能和显微组织的影响。
- Below the lower critical solution temperature (LCST), the polymer is soluble in water because of the strong hydrogen bonding between the water molecules and the NIPAM groups. 在“较低的临界溶液温度”(LCST)以下，因为有水分子和NIPAM基团的强的氢键相互作用，聚合物是水溶性的。
- A new method for preparation of polysulfone hollow fiber ultrafiltration membranes using the lower critical solution temperature (LCST) systems has been developed. 本文探索采用一种新颖的制膜体系和制膜方法制备聚砜中空纤维超滤膜。
- Non-Newtonian Index of 9:1 blend solution at the invested temperature range is lower than 1, which increases with solution temperature and deceases with solution concentration. 共混比为9：1的溶液在不同温度下的非牛顿指数均小于1，并随溶液的增浓和温度的降低而减小。结构粘度指数随溶液温度的升高、体系浓度的减小而减小。
- The solubility of polymers in alcohol mainly effected by the monomer ratio and solution temperature and benefited to increase of the amount of polarized monomer (AA and VAc). 增加极性单体AA和VAc的用量，可以改善聚合物在乙醇中的溶解性；通过结构表征发现，聚合物中AA上的羧基基团易在聚合物里形成氢键而影响聚合物的溶解性。
- If the fountain solution temperature is too high, not only will accelerate the fountain solution and chemical reactions between base also suites up dirty cratering. 如果润版液的温度功矮，不但会增速润版液与版基之间的化学不正答，还会爆不收版面起不净等弊病。
- Solution Temperature: (20-35 c) . Immerse the parts in the solution for 1-2 minutes. Take it out and shake it manually slightly or in a centrifuge. Let it dry in the air. Oven dry at 80-100 c for 20-30 minutes is preferred. 溶液温度20-35℃。零件在溶液里浸泡1-2分钟。出液后稍做抖动或用离心机甩干,再常温晾干,或80-100烘20-30分钟效果更佳
- When the aqueous solution temperature reached the lower critical solution temperature (LCST), the PNIPAAm chain in DgP turned from hydrophile to hydrophobe, which leaded to the fonnation of micelle with PNIPAAm as core and dextran as shell. 当水溶液的温度达到低临界溶解温度(LCST)时,DgP中的PNIPAAm组分发生亲疏水相变,DgP分子相互聚集,形成了以PNIPAAm为内核,Dextran为外壳的稳定的胶束。
- The influence law of particles content in the solution, solution temperature, stirring speed, surface activator etc on the particle content in Ni-P/PTFE composite layer was studied. 探讨了粒子悬浮量、镀液温度、搅拌速度、表面活性剂含量及pH值等工艺条件对Ni-P/PTFE复合镀层中PTFE粒子的含量影响。
- The solid solution RE can decrease the solution temperature of precipitated V(C,N), impede the precipitation of V(C,N) in austenite and accelerate and refine the precipitation of V(C,N) in ferrite. 稀土降低碳氮化钒完全溶解的温度,阻止奥氏体中钒的应变诱导析出。
- Chitin xanthate, cellulose xanthate and their blend solution belong to non-Newtonian fluid, where non-Newtonian Index increases and structure viscosity decreases with increasing solution temperature. 甲壳素黄原酸酯溶液、纤维素黄原酸酯溶液、不同配比的共混溶液均属于非牛顿流体，非牛顿指数随溶液温度的升高而增大，结构粘度随溶液温度升高而减小。
- The electrolytic bath solution temperature invariablenes is the condition precedent that guarantees a product quality and increase production in electroplate,electrochemical and eletron fields. NLS耐腐蚀冷水机 电解槽液的温度恒定，是电镀、电化、电子行业保证产品质量与提高产量的先决条件。
- It may take a long time to find a solution to the problem. 也许要花很长时间才能找到解决这个问题的办法。
- The recrystallization tendency of single crystal superalloys with different levels of carbon at different solution temperatures and compressive stresses was investigated. 摘要研究了不同碳含量镍基单晶高温合金在不同固溶温度和压应变条件下的再结晶倾向性。
- I simply refuse to conceive of such a solution. 这样的解决办法，我是绝对不考虑的。
- What color is copper sulphate solution? 硫酸铜溶液是什么颜色？
