您要查找的是不是：
- One is taper section 3D beam element model, the other is 3D compounding model with solid element and shell element. 结果表明，在均布荷载与集中荷载作用下箱梁的剪力滞效应明显不同，对于地震时程反应分析而言，采用变截面三维梁单元模型计算效率较高。
- solid element modeling 实体单元建模
- Its finite element model is established. 构造了其有限元模型。
- A static finite element model of an air spring was given. 摘要文中建立了空气弹簧的静态有限元模型。
- The three-dimensional thermo-electric solid and finite element model of a great aluminum reduction cell was built based on general finite analytic software ANSYS. 摘要基于通用有限元软件ANSYS建立了某大型铝电解槽结构的三维实体模型和热应力场耦合分析的有限元模型。
- Based on single-crank crankshaft, beam element whole crankshaft and solid element whole crankshaft model, the crankshaft deformation and main bearing load of N485 diesel engine are calculated. 基于单拐曲轴、梁单元整体曲轴和体单元整体曲轴模型，分别计算了N485柴油机的曲轴变形和主轴承负荷；
- all solid elements model 全实体模型
- The respective virtues of beam element and solid element are shown in two modelings. 利用梁单元和实体单元各自的优点，通过二次建模互补进行结构有限元分析。
- The finite element model of opening gap tantalum thin-walled tube is setup. 为了控制钽薄壁管焊接成形的质量,进行钽薄壁管开口间隙场计算模型的研究。
- The results show that the mechanical performance simulated by the established finite element model of the NEPE solid propellants is in good agreement with the experimental regularity. 结果表明,采用所建立的NEPE推进剂轴对称有限元计算模型所模拟的力学性能规律与实验研究的趋势符合得很好。
- According to the structural features of the brake hoof, a three dimensional solid model was built in the finite element software.The finite element model needed was given based on mapping mesh method. 摘要根据制动蹄的结构特点，在有限元环境中建立制动蹄的三维实体模型，并运用映射网格的方法给出所需的有限元模型。
- Finite element modeling has become an important tool for predicting the membrane wrinkling at present. 有限元模拟已经成为目前薄膜褶皱预测的重要工具。
- Based on the traditional solid isoparametric element and shell theory, a new type of degenerated solid element was proposed, with bars modeled using the three-dimensional disperse model. 曲线桥梁极限承载能力的问题,提出采用实体退化单元的三维分析方法。
- The way of building finite element modeling and the geometrical similarity of model are also discussed in the paper. 文中还讨论了有限元建模的方式与建模的几何相似性。
- Coupez T.3-D Finite Element Modeling of the Forging Process with Automatic Remeshing[J].J.Mater Proc.Technol.,1991,27. 赵国群等.;金属成形有限元分析中的网格重划分问题[J];模具技术;1991(1)
- R. A. Stechschulte and J. R. Luchini, "A Laminated Composite Solid Element and Its Application to Tire Analysis," Tire Science and Technology, TSTCA, Vol.15, No.1, pp.42-57 (1987). 高嘉祥;"斜交式机车轮胎之电脑辅助设计";私立淡江大学机工程研究所硕士论文(1989).
- This paper presents a new finite element modeling technique for spot-welds of autobody in vehicle crash simulation. 摘要对点焊连接提出了一种新的模拟技术，即不同于传统的节点对节点模拟焊接。
- The finite element models simulating normal, pre- and post-PFO were created. 再者，可产生模拟正常、病患的股骨近端截骨术术前及术后情形的有限元素模型。
- A tapered beam element model is used to simulate the behaviour of a masonry arch bridge with loading. 采用梯形梁单元分析砖石拱桥在载荷作用下的行为。
- Primary study on the construction of the finite element model of tooth and post-core. 牙齿与桩核三维有限元建模的初步探讨。
