您要查找的是不是：
- At this stage, it's easy to remake a solder connection if there is a problem. 在这一阶段，如果存在问题，可以很容易地改造焊接的连接点。
- Solder Bridging: Solder connecting, in most cases, misconnecting, two or more adjacent pads that come into contact to form a conductive path. 桥接:焊料连接,通常是导线间由焊料形成的多余的导电通路。
- Valve ends shall have full depth aNSI threads or extended solder connections and be manufactured to comply with mss.SP110. 阀门连接端口应该具有足够深度的美国国家标准协会aNSI螺纹,或加长焊接端口,并按照美国阀门和管件制造商标准化协会MSS-SP110标准制造。
- Valve ends shall have full depth aNSI threads or extended solder connections and be manufactured to comply with MSS-SP110. 阀门连接端口应该具有足够深度的美国国家标准协会ansi螺纹,或加长焊接端口,并按照美国阀门和管件制造商标准化协会MSS-SP110标准制造。
- Would you like to have each coil wire spliced using soldered connector or terminal one? 每个线圈的接头时用锡焊方式还是闭端端子扎接方式?
- ANSI B16.18 states that the maximum operating pressure of 50-50 solder connections is 200 psi at 100oF, and decreases with higher temperatures. ANSI（美国国家标准化组织）B16.;18规定50-50焊料连接的最大工作压力在37oC下是200psi，温度越高，则压力就越低。
- If solder connections are used, solder the pipe to the adapter before attaching the adapter to the hot and cold water fittings. 如果需要采用焊接连接方法，要先将管道焊接在连接器上，然后再将连接器连接在热水和冷水接头上。
- The small percent of silver in the solder prevents the silver on the leads from migrating into the solder resulting in a weak or brittle solder connection. 焊料中的少量银成分可以防止引脚上的银迁移到焊料中,从而导致不牢固或脆弱焊接。
- Currently, its seven production workshops are the punch,machine machining, plastic injection , parts assembly , mold construction , solder connection, and furniture mat . 现有冲压、机加、注塑、压铸、装配、模具、焊接、保护垫八个生产车间。
- The wires connect (up) under the floor. 电线是在地板下接通的。
- low temperature solder connection 低温焊料连接
- No reason to connect the two events. 没有理由把这两件事联想在一起
- Can you connect me with Los Angeles, please? 请给我接通洛杉矶的电话，好吗？
- Connect these wires to the leads of the battery. 将这些导线接到电池的引线上。
- Connect the fridge (up) to the electricity supply. 接通冰箱的电源。
- The train is timed to connect with the ferry. 火车时刻编排得可与渡轮运行时刻衔接。
- Insulate the soldered connection and the bare ends of the 4th, 5th, and 6th gear wires to the PGM-III to complete the splice. 隔离焊接连接和裸露的两端第4，第5和第6次齿轮电线的铂族金属三完成剪接。
- Where does the cooker connect with the gas-pipe? 煤气炉在什麽地方与煤气管道衔接?
- Solder it to the inner conductor of your Type N connector (see photo). 用焊锡把它和N连接器的导体焊接起来（见照片）。
- Don't connect up the two wires, or there will be a short circuit. 不要把这两条电线接在一起，否则会短路的。
