您要查找的是不是：
- signaling link failure 信号链路故障
- Signaling Link Code = the member number within a link set. Signaling Link Code = 链路群内的成员号。
- Signaling Link Code--he member number within a link set. Signaling Link Code -- 链路群内的成员号。
- The CHG:SLK command is used to change the minor state of a signaling link. CHG:SLK 命令用于更改信令链路的次级状态。
- Major State of Link = the major equipage status of the signaling link. Major State of Link = 该信令链路的主要设备状态。
- If a connector cannot transfer messages, the advanced queuing engine notifies the routing engine of a link failure. 如果连接器无法传输邮件,高级排队引擎将通知路由引擎链路出现故障。
- The device routes or switches incoming messages to an outgoing signaling link using routing information within the multitiered SS7 message. 该装置为利用多层七号信令报文中的路由信息，为进来的报文送到输出的信令链路上建立路由或进行交换。
- The SS7 environment provides rerouting, error correction and retransmission capabilities for continuous service in the event of signaling point or link failures. 七号信令环境在信令点或链路失效的情况下为提供连续的服务，提供了重建路由、纠错和重新发射的功能。
- This state Indicates that the AP-DS1 is available for use by an RCS signaling link. 该状态表明 AP-DS1 可供 RCS 信令链路使用。
- Link Node Address (Group and Member) = the node within the IMS ring on which the signaling link terminates. 链路节点地址 (Group and Member) = IMS 环路内信令链路终止的节点。
- If you use X.400 connectors, and the connector cannot transfer messages, the Exchange MTA informs the routing engine that a link failure occurred. 如果使用X.;400连接器;但是该连接器无法传输邮件;则xchange MTA会通知路由引擎发生了链路故障。
- Signaling links are usually equipped in pairs in SS7 networks. 信令链路常常是成对地装配在 SS7 网络中。
- When Exchange queuing notices a link failure to the bridgehead server on a connector, routing relays this information to the routing group master. 当Exchange队列将链接故障通知给连接器上的桥头服务器时,路由将此信息中继给路由组主服务器。
- Signal unit initial alignment - invokes initial alignment prior to activating or restoring a signaling link. 信令单元初始定位 -- 在激活或恢复信令链路之前调用初始定位。
- The improved DSR greatly increasesboth the available bandwith for upper layer traffics and the accurate level of thedetection of the link failure. 改进后的DSR协议为上层业务提供的可用带宽和对链路失效的判断的准确度都大大提高。
- A link control protocol is defined for the mult-link management to control link identification, link blocking and link failure conditions. 链路控制协议被规定用于多链路管理来控制链路标识，链路阻塞和链路故障状态。
- The SS7 environment provides rerouting,error correction and retransmission capabilities for continuous service in the event of signaling point or link failures. 七号信令环境在信令点或链路失效的情况下为提供连续的服务，提供了重建路由、纠错和重新发射的功能。
- The s7ln form (SS7 link) is used to define the individual SS7 signaling links. s7ln 表(SS7 链路)是用于定义各 SS7 信令链路。
- Far-End CLLI = the Common Language Location Identifier (CLLI) that is associated with the STP or 5ESS DCS at the far end of this signaling link. Far-End CLLI = 与该信令链路远端处的 STP 或 5ESS DCS 相关的公用语言位置标识符 (CLLI)。
- Each signaling link may accommodate a traffic load of approximately 40 percent of its maximum load capacity. 每一信令链路可容纳其接近最大负载能力 40%25 的话务量。
