您要查找的是不是：
- The dehumidified veneer is of good flatness and small shrinkage ratio. 干燥后的单板平整度好，收缩率小。
- The intensification of immiscible element in this process is the key to realize uniformization sintering and reach a higher shrinkage ratio. 加强非西安理工大学硕士学位论文一互溶性组元在此方面的功用作用是实现此类材料均匀化、高收缩比烧结的关键。
- The adhesive is characterized with such good qualities as good optical performance, hige adhension, rapid photocuring, and low volume shrinkage ratio. 试验表明，该胶具有光学性能优良，粘接强度高，固化定位速度快，低收缩率，耐高低温变性好等优点。
- When the content of 316L kept constant, the relative density, shrinkage ratio and HRC value of the sintered samples decreased with the increase of 316L particle size. 在316L含量一定的情况下，随着316L颗粒尺寸的增大，复合材料的密度略有降低，相对密度和线收缩率逐渐减小，试样的HRC硬度值下降。
- The effects of polypropylene fiber on the plastic shrinkage stress and plastic shrinkage ratio of the mortars were investigated by use of a self-designed measuring device. 采用自行研制的水泥砂浆塑性收缩应力测试装置和非接触式测长装置,分别研究了低掺量的聚丙烯纤维对水泥砂浆塑性收缩应力和塑性收缩率的影响。
- The molding size was designed according to the average shrinkage ratio of polystyrene,demoulding mechanism of taper microgroove and arc side core-pulling mechanism was used in the mold. 按聚苯乙烯的平均收缩率设计计算模具成形尺寸,在模具中设计了圆锥细纹脱模机构、弧形侧抽芯机构。叙述了模具成形零件的设计与加工工艺过程、浇注系统和其它结构的设计过程,并介绍了模具工作过程。
- Shrinkage ratio of size after heated 受热尺寸收缩率
- shrinkage ratio of cross section 断面收缩率
- There has been some shrinkage in our export trade. 我们的出口贸易量已有些减少。
- Research of Polypropylene with Low Mould Shrinkage Ratio 低模塑收缩率聚丙烯的研究
- It's best to allow for shrinkage when buying cotton clothes. 买棉布衣服时最好考虑到它们的缩水率。
- Study on solidified shrinkage ratio of resin for FRP door and window profile FRP门窗型材用树脂固化收缩率的研究
- The ratio of students to teachers is 35:1. 学生和老师的比率是三十五比一。
- The ratio of schoolboys to schoolgirls is 2 to 1. 男学生和女学生的比例是2比1。
- As a result of shrinkage, the shirt is now too small to wear. 由于洗后缩小，那件衬衫现在小得不能穿了。
- Men outnumber women here in the ratio of three to one. 此地男子数量以三比一超过女子。
- The first or last term of a ratio or a series. 首项，末项比率或数列中第一个或最后一个项
- Analysis of Influencing Factors on the Shrinkage Ratio of Crystalline Plastics Injection Molding Products 结晶型塑料注射制品收缩率影响因素分析
- Controlling shrinkage ratio and surface-quality through optimization of process conditions in SMC molding 优化SMC模压工艺控制制品收缩率和表面粗糙度
- Allow two inches in the fabric for shrinkage. 在织物上预留两英寸以免缩水
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries
