您要查找的是不是:
- Derived results are able to reflect the influence of the quality of a material to them,compared with the result from the shear strain energy strength theory. 导出的结果与由剪切应变能强度理论得来的结果相比,能够反映材质的不同对疲劳极限条件的影响。
- critical shear strain energy theory 最大剪应变能量理论
- shear strain energy 剪应变能
- It was analysed by a strain energy method. 这是用应变能力方法解决的。
- The shear strain can be determined in the following way. 用下列方法能够确定切应变。
- Shear strain in MBE grown CdTe films on Si(211) substrates[J]. 引用该论文 王元樟;陈路;巫艳;吴俊;于梅芳;方维政;何力.
- The proof was based on the nonnegativeness of the strain energy. 这种证明根据的是胁变能量的非负性。
- The strain energy density function equals the Helmholtz. 应变能密度函数等于亥姆霍兹函数。
- The transformation is due to the shear strain imposed on the specimen by ECAP. 该转变发生是由于ECAP过程中材料承受剪切应变,应变能累积诱发再结晶,从而形成等轴晶双相结构。
- LCF life could be well expressed by plastic strain energy. 低周被劳寿命可由塑性应变能表达。
- The computing formulae of the shear moduli of SWCNT are obtained by comparing the total molecular potential energy of a SWCNT with the strain energy of a corresponding thin cylinder. 通过总势能与相应的薄壁圆筒的扭转变形能比较,推导出了单壁碳纳米管剪切模量的计算公式;
- The only strain is a shear strain and the dilatation is zero, these waves are called shear waves. 唯一的应变是剪应变而没有膨胀,这种波叫剪切波。
- Good bonds are always accompanied by surface extension, that is, plastic shear strain. 良好的键合总伴有表面延伸即塑性切向形变。
- The total strain energy of laminated shell is deduced by means of Ritz method. 接着本文研 究了非对称正交层合壳的固化变形特性。
- Variation of Damping Properties Under Magnetic Field and Shear Strain Amplitude in Fe-Cr-Al Alloys. 高阻尼Fe-Cr-Al合金在磁场和应力场下的阻尼行为
- The elasticity of copolyester increases with the shear strain but decreases with the temperature. 弹性随切应力的增大而增大,随温度的升高而降低。
- Lighting, heating, and airconditioning in the skyscrapers strain energy supplies. 大楼里的照明,暖气以及空调造成能源供应紧张。
- The residual strain is the additional shear strain created with the increase of pore pressure due to cyclic shear under initial shear stress. 残余应变是由于周期剪切引起孔隙压力增长;在初始剪力作用下产生的附加的剪应变.
- The results show that the data of shear strain 2 are reliable because the component 2 and 4 of shear strainmeter work normally. 通过对标定系数和滞后时间的分析认为:元件2、4工作状况比较稳定,观测值差应变2是比较可靠的;
- Moreover, high value region of maximum shear strain and superficial expansion in this area is in Tianjing, Beijing, Tangshan area. 区内最大剪应变、面膨胀的高值区在天津、北京、唐山一带。