您要查找的是不是：
- The Feature of Wedge Ramp for Self locking Nut 楔紧自锁螺母的特征分析
- self locking nut 自销螺母
- Install adjuster nut and lock nut. 安装调节器螺母和防松螺母。
- Lock handle securely by turning lock nut clockwise. 3、顺时针方向拧紧螺帽，可靠的锁好把手。
- A self - locking nut. 自锁螺母
- Remove the locking nut from the flow/conductivity/temp sensor. 移开流量/导电/温度传感器上的固定螺丝。
- Use to unscrew Flame Adjuster Nut & Pump’s Stop Nut. ---用来旋松火焰调节器螺帽和泵的限位螺帽。
- Remove the locking nut from the flow / conductivity / temp sensor. 卸除流量/电导/温度传感器上的锁紧螺帽。
- To Readjust- Loosen lock nut on the adjusting screw. 重新调节：松开调节螺丝上的锁定螺母。
- To Readjust - Loosen lock nut on the adjusting screw. 重新调节：松开调节螺丝上的锁定螺母。
- Revolving the lock nut 5 anti-clockwise to the suitable position. 逆时针方向旋转锁紧螺母5;使其退到适当位置.
- Operator is a self locking worm gear type. Equipped with adjustable stops at open and shut positions. 操作装置是一种自锁定蜗轮类型。具有在开启和关闭等位置进行调节的锁定功能。
- A unified formula is derived for efficiency of H closed epicyclic gear train.In addition, self locking conditions of ... 并在此基础上 ,推导出 H封闭式周转轮系的效率计算的统一公式 ;
- Disc is fastened securely to disc hanger with a lock nut and cotter pin. 通过一个锁紧螺母和开口销将阀瓣安全紧固在阀瓣支架上。
- You can adjust turns tension by tightening the inside stop nut on the rotor shaft against the backplate to provide a more pleasing tension. 我用硬质合金尖划针作标记, 当然任何尖的物体均可利用。必要时，你也可以使用铅笔圆规的针尖作标记。分开你刚才标定的动片和定片。将所有的定片叠在一起。
- Smaller sizes use a lock nut with a locking washer (a), larger sizes use a nut with locking clip (b). 小尺寸轴承使用带锁紧垫圈的锁紧螺母(a)大尺寸的轴承使用带锁紧卡箍的锁紧螺母(b)。
- This control effect can be got by designing the size of pokedwheel,using the self locking character of worm wheel and worm pole and connecting the pawl mechanism with overtravel ... 通过有效设计拨轮的尺寸，利用蜗轮蜗杆的自锁特性，将棘轮机构与行程开关联为一体，达到自动输球控制的目的。
- If only one locating ring is required, it should be inserted on the same side as the lock nut. 如果只需一个定位环,此定位环应插入与锁紧螺母相同的一侧。
- The first product we developed and completed based on this theme was the Hard Lock nut. 我们以此为出发点,开始了研究开发,经过不断实验终于研究成功了Hard Lock螺母。
- Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening angle. 孔径最大为100毫米的小型轴承可通过测量锁定螺母的紧固角度正确安装。
