您要查找的是不是:
- section bar wall thickness 型材壁厚
- Range Min and Max.-OD with wall thickness. 范围分钟和最大Od以壁厚度。
- The needed pipe bending moment、wall thickness reduction and ovality of section are known by simulating. 通过模拟,计算管子弯曲变形所需的弯矩,计算管子弯曲部分外壁减薄率和椭圆度。
- Eccentricity. A condition of pipe in which the OD and ID axes are not coincident, resulting in wall thickness variation around the circumference at a given section plane. 偏心。管子内外表面中心轴线不重合,使得某一给定截面处的壁厚沿圆周方向不均匀。
- The backing of bearings with greater wall thickness is not copper-plated. 轴承壁较厚的轴承,其背衬不镀铜。
- APACO processes Hardboard, MDF or Chipboard up to a wall thickness of 18mm. 橱柜/壁柜/橱柜门板/人造石厨房台面加工制作.
- The paper analyses the stress wave propagating in a variable section bar using HONDO finite element computer program . 利用HONDO有限元程序对应力波在变截面杆中的传播进行了分析。
- The forecasted wall thickness was conformed to the experimental result. 预测的壁厚和实验结果吻合得很好。
- Use four the hard mass alloy milling cutter , once to be milled on the section bar outing the correct tenon mouth. 使用四把硬质量合金铣刀,一次在型材上铣出正确榫口。
- The wall thickness of the profile should be well-proportioned, the quantity of the single arm should be controlled, the cross of the section should be avoided, and the shape of the sect... 壁厚要尽量均匀,尽量减少单臂,尽可能避免截面有交叉重叠,并尽量简化截面形状。
- Click the section bar of the group header or footer for the group level you want to merge into the next lower group level. 单击需合并至相邻的下一级分组级别的组页眉或组页脚的节栏 。
- It is thought through actual case analysis that elastic unstability of crossing section is unlikely to occur in crossing steel pipelines when conformable with minimum wall thickness limit as per... 通过实例分析,认为穿越钢管道在满足规范要求最小壁厚限制时,通常不会发生横截面的弹性失稳,即刚度控制的实质为强度控制。
- End connection including wall thickness of connecting pipe if weld end and any special flange facings or finishes. 连接方式,如果是焊接端口和任何法兰面或表面,则包括连接管道的壁厚。
- What is the foundry's checking frequency for control of core shift and wall thickness? 工厂检验芯偏移以及壁厚的频率?
- The tube deformation characteristics on ASSEL mill are deformation concentrating at shoulder and wall thickness in rolling zone increasing. ASSEL轧管机具有台肩集中变形、碾轧段壁厚增厚等特点。
- Hand movement hacksaw machine: Be used to break various aluminium alloy doors and windows material up mainly , also may be used to cut off other aluminium alloy section bar cutting. 手动锯床:主要用于切断各种铝合金门窗料;也可用于切断其他铝合金型材切割.
- The wall thickness of a 1-litre bottle preform is 3mm. The cooling time is 10.8s. 1公升的矿泉水瓶瓶坯壁厚3mm,冷却时间便占10.;8秒。
- The wall thickness of a 5-gallon bottle preform is 8mm. The cooling time is 76.8s. 5加仑瓶瓶坯壁厚8mm,冷却时间是76.;8秒。
- When chilled water is used to cool the mould, cycle time is related to wall thickness as follows. 在冰水冷却的条件下,冷却时间与壁厚有以下的关系。
- The aorta wall thickness (AWT) was measured wiht B-mode echocardiography in 128 patients with primary hypertension. B型超声心动图下测量了128例高血压病患者主动脉壁厚度(AWT),同时检测了血脂指标。