您要查找的是不是:
- Improvement on Sealing Face Leakage of Plate-Type Filter 板式过滤机滤箱密封面渗漏的改进
- sealing face leakage 密封面泄漏
- The primary and mating seal faces are lapped to a maximum of 3-helium light bands flatness to provide effective sealing and leakage protection. 主密封面和配套密封面叠加成最多3层的轻型带状平面,提高密封和防泄漏效果。
- The inner mechanical seal shall be constructed with a solid block carbon rotating seal face and a solid block silicon carbide stationary seal face. 内置的机械密封结构应该采用一块整体结晶碳旋转密封面和一块整体结晶碳化硅固定密封面。
- Caution: Do not allow purple primer or solvent cement to come in contact with the sealing face of the end connectors. 警告:不要让紫色底漆或液状粘固剂进入接触到端口连接件的密封表面。
- Surfacing technology of Ni-alloy to improve the sealing face of valve was introduced. 介绍了一种改善旋转止回阀密封面性能的镍基堆焊工艺。
- It is of built-in type, single seal face, single spring and rubber-bellows mechanical seal. 内装式、单端面、单弹簧、橡胶波纹管机械密封。
- The friction performances of laser-textured porous seal face were experimentally investigated. 对激光加工多孔密封端面的摩擦性能进行试验研究。
- Changes in the spring performance will directly affect the mechanical seal face pressure. 弹簧性能的发生变化将会直接影响机械密封端面比压。
- Because the hermetic sealing weir reduces expenses the action, the gas of the entry hermetic sealing face is compressed, the gas press goes up. 由于密封堰的节流作用,进入密封面的气体被压缩,气体压力升高。
- Precision ground blade on both sides for tighter packing chamber sealing. Sealing face of the gate is lapped to provide the best possible seat tightness. 两侧都经过精密光亮磨光的刀片确保填料腔的气密性密封。闸板的密封面经过研磨,以提供最好的阀座密封性。
- The outer mechanical seal shall be constructed with a solid block silicon carbide rotating seal face and a solid block silicon carbide stationary face. 外置的机械密封应该采用一块整体结晶碳化硅旋转密封面和一块整体结晶碳化硅固定密封面。
- When the operating medium contains some granules, you can squirt lotion or lubricant to clean the seal face, making sure a reliable seal. 当输送的介质不洁或含有少量颗粒时,为保护密封面,确保达到可靠的密封,还可给这一装置注射相应的清洗剂或润滑剂对密封面进行清洗。
- The parametric study demonstrates that substantial hydrostatic pressure can be produced on the seal face with partial micro-pores. 研究表明在部分密封端面上加工微孔可有效增大端面静压。
- The seal characteristics influenced by the geometry parameters of the grooved seal face were discussed,the optimized geometry parameters were suggested. 并探讨了各种结构参数对密封性能的影响规律,对密封的设计、制造及应用具有一定的指导意义。
- The outer mechanical seal shall be constructed with a solid block silicon carbide rotating seal face and a solid block silicon carbide stationary seal face. 外置的机械密封应该采用一块整体结晶碳化硅旋转密封面和一块整体结晶碳化硅固定密封面。
- As a typical example,the spiral grooved gas face seal was analyzed in detail with the consideration of seal face's waviness and taper through finite element method. 本文以螺旋槽气体润滑机械密封为研究对象,采用有限单元法分别对周向波度、径向锥度对其低速运转性能的影响规律进行了较为详细的分析研究。
- The two sealing faces are made out of anti-wear-out and Tungsten Carbide for suppression of mechanical jolt. 两个封闭面是碳化钨材料所制成,而这个材质是特别抗磨损和机械突震。
- It is a fact of life and you must face it. 这是严酷的现实,你必须面对它。
- He tried to put a bold face on his failure. 他对自己的失败装出一副满不在乎的样子。