您要查找的是不是:
- The relation between extrudate density and screw speed,die temperature is also discussed. 还揭示了口模温度和螺杆转速与制品密度的关系。
- Test wells were safe separation of oil-water mixture, the best screw speed of 110 rev / min. 试验井油水混合液被安全分离,最佳螺杆泵转速为110转/分钟。
- Increasing the screw speed increased the extrudate's longitudinal expansion and lightness value. 而产品之纵向膨发以及亮度值会因而增加;
- The influences of screw configuration,screw speed,extrusion temperature and water contents on extruded starch foams were studied. 研究了螺杆组合、螺杆转速、挤出温度以及含水量对淀粉挤出发泡的影响。
- Experimental outcome indicated that increases in screw speed and decreases in feed rate improved the de-gossypol results. 结果表明:增大螺杆转速、减低喂料速度,脱毒效果变好。
- The increase of screw speed resulted in increasing extrudate's sectional expansion ratio, however, decreasing extrudate's puncture force. 螺轴转速增加 会导致产品膨发率增加、穿刺力减少。
- Phases 2(3)temperature control, ejected speed. Backing pressure and screw speed is suitable for various plastic to confectioned. 二(三)段温度控制,射速,背压,螺杆转速无段调整适合各种精密塑胶之零件成型。
- It was found that at the higher screw speed, the higher draw rate and the lower processing temperature the PA6 fibrils were finer and the mechanical properties of PP/PA6 compos... 发现当螺杆转速越高、牵引速率越快、加工温度越低,分散的PA6纤维尺寸越小,复合材料的力学性能越好。
- The response surface methodology was used to study the influences of screw speed, barrel temperature, material moisture arid enzyme mass fraction on DE values. 采用响应面分析方法研究了螺杆转速、机筒温度、物料水分和酶质量分数对挤出物DE值的影响规律。
- The effects of compostion,viscosity ratio of the minor to major phases,screw speed and mixing time on the viscosities and morphology of polybutenes/corn syrup blends were studied. 研究了组成、粘度比、转速和混合时间对聚丁烯/玉米浆共混物的粘度和形态的影响。
- The results show that the forming bubbles can be effectively prevented and the high-speed extrusion without bubble can become the truth through adjusting the screw speed, increasing the die gap and selecting the suitable processing conditions. 实验表明:通过调整螺杆转速、加大机头口模间隙及选择适当的工艺条件,可以有效地防止气泡的产生,实现无泡高速挤出。
- The effects of process parameters include feed moisture content(FMC), barrel temperature(BT), feed speed(FS) and screw speed(SS) on physico-chemical properties, texture properties of extruded products were studied. 以最优工艺参数下的产品为试验材料,对产品的干燥、复水、蒸煮、冻融、油炸、风味与色素吸附和贮藏等特性做了试验和分析。 结果表明:1、随着物料水分含量的升高,产品的亮度指数、有效赖氨酸含量和组织化度逐渐升高;
- It was found that at the higher screw speed, the higher draw rate and the lower processing temperature the PA6 fibrils were finer and the mechanical properties of PP/PA6 composites were better. 发现当螺杆转速越高、牵引速率越快、加工温度越低,分散的PA6纤维尺寸越小,复合材料的力学性能越好。
- It was employed that changing the processing temperature, screw speed and draw rate in order to study how PP/PA6 in-situ fibrillation composite was affected by the processing conditions. 在PP/PA6共混物的挤出加工中分别调整加工温度、挤出机螺杆转速、牵引速率,得到不同加工条件下的PP/PA6原位成纤复合材料。
- A systematic study was performed on the extruder set via analyses of the factors such as feeding, screw speed, throttle valve, screen pack changer, die plate and pelletizer, aimed at saving energy. 选择进料状况、螺杆转速、节流阀、换网器和模板及切粒机等因素对挤出机机组的影响进行了系统分析、研究,发现这些因素对挤出机的负荷和能耗影响较大。
- I can't get this screw to come out of the wall. 我无法把这颗螺丝钉从墙上取出。
- No horse has a speed comparable to that of his. 没有一匹马的速度能比得上他的马。
- The brackets want an extra screw. 托架需要再加一个螺钉。
- Increasing screw speed (unfilled only) 提高螺杆速度(仅在未装入时)
- That's all there is to make a speed dial call. 在那里全部要进行快速拨号呼叫。