您要查找的是不是：
- The influence of rolling speed is not distinct. 轧制速度对界面结合的影响不明显。
- The splitting rolling technology was applied to reso lve the problems of slow rolling speed, low productivity, etc. 针对嘉良钢铁公司棒材半连续式水平连轧机组轧制速度慢、产量低等问题,采用了切分轧制技术;
- While the rolling speed exceeds 2 m/s, the variation of heat drop gradually tends to become gentle. 制订轧制规程时，出炉温度可选择合理范围内的较低值以降低能源损耗；
- It is important to match rolling speed with other equipment that assure stably working and improve quality of product. 处理好热卷箱与轧机的速度匹配关系对稳定生产和提高产品质量至关重要。
- I felt matchless joviality excited by the rolling speed and the piping alt tone, and was unwilling to be back to the ground! 我被旋转的速度和高得略带嘶哑的高音刺激得无比愉悦，根本不愿回到地面!
- At a low steel rolling speed, the traditional AGC feedback control is not very good due to a long time delay caused by the thickness measurement. 在低速轧钢时,由于测厚仪测量值的长时间滞后,传统的后馈控制效果不好。
- The forecasted film thich-ness from the computation and the critical rolling speed was close corelated to the practical status... 计算得出的不同轧速下膜厚预报值以及临界轧速与实际数据吻合。
- This paper gives the dynamic programming method and example for rolling speed optimization to reach minimum energy consumption rate. 文中阐述了以动态规划法按轧制总能量最小对轧制速度进行优化的方法及实例。
- Select the Rolling Speed at the pull down menu, then hold down the left click on the [ Rolling Up ] or [ Rolling Down ] to control the destination blind. 于下拉选单选好搅动速度后，用滑鼠左键按下[上移]或[下移]控制地点牌。
- Two fluting regimes are found under the influences of supply voltage, supply current, oil film thickness, and rolling speed, namely, fluting and non-fluting regimes. 另外，建立由电蚀形态门槛，滚动速度、油膜厚度及供应电压与电流关系所构成之电蚀形成图可分为凹凸条纹纹路与非凹凸条纹纹路区域。
- It is pointed out that like the barrel type piercer process,the control of the cone type piercer roll speed is also very important. 指出了锥形辊穿孔机也要和桶形辊穿孔机一样,要重视对穿孔机轧辊转速的控制。
- Setting main parameters of disc flying shears are presented in detail. including cut angle, bite conditions, amount of scissors overlapping, friction coefficient and rolling speed etc. 详细介绍了圆盘式飞剪各主要参数的确定，包括交角、咬入条件、剪刃重叠量、摩擦系数、轧制速度等。
- Bearings with a tapered bore are used when an interference fit is required for the inner rings on the roll neck, e. G. When rolling speeds are high. 在轧辊轴颈上的内圈需要过盈配合时,例如轧钢速度高时,使用带锥形孔的轴承。
- No horse has a speed comparable to that of his. 没有一匹马的速度能比得上他的马。
- Chock the barrel up or else it will roll over. 用楔子塞住圆桶,不然它会滚过去。
- The comedian soon had them rolling in the aisles. 那滑稽演员很快就逗得他们捧腹大笑。
- The national debts of that country are rolling up. 那个国家的国债在不断地增加。
- He's a rolling stone and got no where all his life. 他见异思迁，毕生一事无成。
- That's all there is to make a speed dial call. 在那里全部要进行快速拨号呼叫。
- Smoke was rolling up from the burning oil up smoke. 正在燃烧的汽油箱上浓烟滚滚。
