您要查找的是不是：
- roller type size applicator 辊式单丝浸润器
- Ready for roller type &presser foot. 备圆轮式与平押式押脚两种。
- belt type size applicator 带式单丝浸润器
- A printer's unit of type size, equal to 12 points or about 1/6 of an inch. 12点活字打印机铅字大小的单位，相当于12点或大约1／6英寸。
- And increase the type size of all days of the week. 都设置为倾斜,并增加这一周中的每一天的类型尺寸。
- A type size, approximately5 points. 五点半铅字一种印刷字体，大约5降?
- The effect of type of sizing applicator is insignificant. 浸润器的类型的影响不显著。
- When type size change design, not separate informs. 机型尺寸变更设计时，不另行通知。
- We could get more lines on the page if we reduced the type size. 如果字体小些，每页还可以多写几行字。
- A printer's unit of type size,equal to 12 points or about!. 12点活字打印机铅字大小的单位，相当于12点或大约！
- A type size for typewriters, providing ten characters to the inch. 打印机活字的尺码，每英寸字行十个字体
- Type GC-D is a roller type freewheel non-bearing supported, Earrings are required to support axial and radial loads. GC-D系列为无轴承支撑滚柱式单向离合器。
- Description: Type GC-A is a roller type freewheel non-bearing supported.Nominal outside diameter is a standard ball bearing dimension. 系列为无轴承支撑滚柱式单向离合器，外部尺寸与标准轴承尺寸相同。
- To find out the characters per pica of a type face at a particular type size copyfitting tables are available for this purpose. 要找出某一字体在某字大小下;每派卡的字符数量;可以查阅[配稿字数表].
- It points out that the principle of hacking is low speed, centrifugal force is the key for separating, and roller type comber should be adopted, which causes little damage to apocynum fiber. 指出开松的原则是“低速度、慢开松、小密度”；分离的关键是离心力的大小，必须考虑终末速度和腾空速度；梳理成形则应采用完全罗拉式梳理，对麻纤维损伤小。
- Type series: The range of type sizes on one typeface design. 字系:同一字体设计的一系列字大小。
- It points out that the principle of hacking is low speed,centrifugal force is the key for separating,and roller type comber should be adopted,which causes little damage to apocynum fiber. 指出开松的原则是“低速度、慢开松、小密度”;分离的关键是离心力的大小,必须考虑终末速度和腾空速度;梳理成形则应采用完全罗拉式梳理,对麻纤维损伤小。
- Description: Type GC-C is a roller type freewheel non-bearing supported.Nominal outer diameter is the same as a series 62 ball bearings.Bearings are required to support axial and radial loads. 产品说明： 型号 GC-C 特性及应用: GC-C系列为无轴承支撑滚柱式单向离合器，外形尺寸与62系列标准轴承相同。
- In other cases, such as using a drop-down to adjust type size in a word processor, this can seem quite natural. 在另一些情形下，比如字处理软件中使用下拉列表来调整字体的大小，这种用法看起来还比较自然。
- Note any visual restrictions; for example, type size or limitations to using color. 任何视觉限制都要提醒,比如文字大小或者颜色限制。
