您要查找的是不是：
- Prime Quality Hot Rolled Sheet in Coil, Unpickled, Unoiled. 热轧高钢卷，非酸洗的，不上油的。
- Simple introduction of engineering of cold rolled sheet of Tangshan Iron and Steel Co. 唐钢冷轧薄板工程介绍。
- Loop analysis of continuous pickling line for cold rolled sheet of Tangshan Iron and Steel Co., Ltd. 冷轧薄板连续酸洗线的活套分析。
- Technology characteristics of cold rolled sheet unit of Benxi Steel Posco Cold Rolled Co., Ltd. 本钢浦项冷轧薄板机组的工艺特点。
- Today large quantities of lead still go into the manufacture of rolled sheet and extruded pipe. 今天，大量的铅仍然用来轧制成铅板或挤压成铅管。
- These housings (series P) are produced from cold rolled sheet steel and are protected against corrosion by a yellow chromate surface treatment. 这些轴承座(系列P)用冷轧钢板制造,表面经过黄色镀铬处理,以防腐蚀。
- Rotary spindle is an important component in the crossbreaking payoff reel of cold rolled sheet plant,which directly effects the normal production. 回转接头是冷轧厂横切开卷机组中的重要部件，它的好坏直接影响到机组的正常生产。
- Present investigation is focused on the recrystallization characteristic of drawable cold rolled sheet steels during rapid heating. 本文研究了冲压钢冷轧薄板在快速加热条件下的再结晶特点。
- The Cu bearing hot rolled sheet steel is a heat treatment strengthened steel, and its strength is increased by 200 MPa by short time heat treatment after forming. 含铜热轧薄板是一种热处理强化类型钢，经时效热处理使铜析出，产生强烈沉淀硬化，钢的抗拉强度在原基础上提高200MPa以上。
- The macroexamination and micro-examination of the characteristics of the common cavity defect in cold rolled sheet of low carbon Al-killed steel were carried out. 对生产中常见的低碳铝镇静钢冷轧板孔洞缺陷特征进行了宏观和微观分析。
- CR coil ( main species: CR coil, cold Rolled sheet ) Provides the corresponding for the automobile industry, appliance industry, daily necessity industry, furniture industry and acquire the very high evaluation of customer. 冷轧卷板(主要品种:冷轧卷、冷轧盒板)为汽车行业、家电行业、日用品制造行业、家具行业等提供相应的产品需求,周到的服务获得用户极高的评价。
- The Cu bearing cold rolled sheet steel has excellent deep drawability as IF steel, and its strength exceeds upper limit of IF steel. The steel has a very high r value of 1.90 and a tensile strength of 590 MPa. 含铜冷轧薄板在保持IF钢优良深冲性能的基础上，其强度超过IF钢的强度上限，该钢平均塑性应变比高达1.;9，抗拉强度可达590MPa。
- According to the surface observation of cold rolled sheet with the calculated results, the relationship between the tribological condition and the surface quality is systematically examined. 轧延后的试片表面经过观察分析后,配合前述数据的结果进行摩擦润滑状况与表面品质良否的相关性分析。
- Install top layer (Pre-fabricated black rubber shred roll sheet) in one direction. Gaps between roll sheets can allow material expansion. 同一方向铺设表层（黑橡胶粒预制板）。板间为材料的胀缩留下缝隙。
- A sheet of hammered, rolled, or cast metal. 金属板锻造、轧制，或铸造而成的金属板
- The mechanical property of AZ31 magnesium alloy rolling sheet under different temperatures and strain rates was studied through uniaxial tensile test. 通过单向拉伸试验研究了AZ31镁合金轧制板在不同温度和应变速率下的力学性能。
- Aluminum alloy garage door rolling sheet parameter table(Note:M is leather strip with silencer,W is leather without silencer. 铝合金车库门帘片参数表（注：M为带消音皮条，W为不带皮条）
- Chock the barrel up or else it will roll over. 用楔子塞住圆桶,不然它会滚过去。
- This caster substituting a single casting phase for all the casting seatting heating breakdown and hot rolling operations normally rogard to prepuce aluminum roll sheet. 它以简单的工艺代替了热轧铝带所需的全部铸坯、机械处理、加热、开坯及热轧工序。而其生产的铝带卷是铝带轧机及铝箔轧机的材料。
- The letter was written on a single sheet of paper. 这封信只用一张纸写成。
