您要查找的是不是:
- Fabrication method of ring test specimen for filament -winding reinforced plastics 纤维缠绕增强塑料环形试样制作方法
- ring test specimen 环形试样
- Is a wedge test specimen utilized for chill or analysis control? 是否用楔型试块进行分析控制?
- Standard Practice for Fabrication of Ring Test Specimens for Glass-Resin Composites 玻璃树脂合成物环形试样的制作
- The finite element model of a small punch test specimen of 1Cr0.5Mo steel is established. 基于小冲孔蠕变试验 ;建立 1Cr0 .;5Mo耐热钢小冲孔蠕变试样的有限元模型。
- The spectr al reflectance of each test specimen is measured in situ before and after exp osures. 在辐照前后对每一个试样的光谱反射系数进行了原位测量。
- The test specimen shall be immersed in the measuring electrolyte so that the top edge of the area to be measured is level with the surface. 测试样本应浸在电解液中,并使测量区的顶端与液面持平。
- The test specimen may be titrated with the Reagent directly, or the analysis may be carried out by a residual titration procedure. 待测样品可能会被卡尔试剂直接滴定,或者采用回滴定法完成分析。
- Although only then several millimeters are long, but each test specimen includes several thousands has not grown the complete egg. 虽然只有几毫米长,但每个试样含有数千未发育完全卵子。
- The sterilizing effectiveness has been verified by Holo Test and Film-cove ring Test. 用抑菌圈法和薄膜覆盖法检测了釉面砖的抗菌效果。
- Report the viscometer model and spindle, the apparent viscosity at the spindle/speed used, and the test specimen temperature. 记录粘度和锭子,外观的粘度在锭子/和使用的速度,还有测试样品的温度。
- In this thesis, we use the oscillation ring test methodology to test stuck-at faults for sequential circuits. 摘要:在此篇论文中,我们利用振荡环测试的原理来侦测序向电路上之定值障碍。
- The measuring objectives are selected software controlled in dependence of the test specimen parameters, must be inserted however manually into the mount. 由软件选择样品被测参数,被测物必须用手装入装配台。
- Inhibition ring test and AATCC 100 test are used to examine the antibacterial property of bamboo pulp fiber and its fabric. 采用抑菌环与AATCC100法对竹浆纤维及其织物的抗菌性进行实验,结果显示未经处理的竹浆纤维中存在抗菌物质,具有良好的抑菌效果;
- In the second part, a test program to help improve modeling of SCBF systems is described, including the design of a nearly full-size, two-story SCBF test specimen. 在文章的第二部分描述了一个帮助轴心抗拉构件改进建模的实验程序。这部分包括一个接近实际大小的两层轴心抗拉构件的实验范例。
- The single fiber pull-out method and NOL ring test were used to characterize the surface modification properties of UHSPE fiber. 通过单丝拔出法及NOL环试验对UHSPE纤维表面改性处理进行了表征。
- To produce a pre-determined depth of angle for different impact test specimen material, this device has double thickness gauges and speed adjustor for depth measurement. 简介制作冲击试验机试片之缺口用,本机可调整切口之深度并附良测之设备,本机具切削速度调整可视材料之软硬等状况调整切削速度。
- Used the gold, analysis test method and so on XRD, TEM agglutinates the after test specimen to the vacuum to carry on the microscopic organization analysis. 采用金相、XRD、TEM等分析测试方法对真空烧结后的试样进行了微观组织分析。
- The representative volume of colluvial deposit is larger tha n normal sized testing specimen. 然因崩积层不易取样以及取样后之代表性不足,造成崩积层工程特性研究之困难。
- The following tests and measurements shall be performed on the same test specimen. 以下测试和测量应在同一样本上进行。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries