您要查找的是不是：
- reverse cylinder valve arm 回动汽缸阀臂
- reverse cylinder valve body cap 回动汽缸阀体盖
- reverse cylinder valve stem 回动汽缸阀杆
- Attach threaded end of stem to the brass valve arm. 将杆螺纹端附加到黄铜臂上。
- The stove and cylinder valve's copulae, use tie-in double pressurize device. 卡炉与气瓶阀门的接合部位采用接头双重密封装置。
- Attach brass valve arm to plastic valve arm with thumbscrew provided. Make sure serrations mesh properly. 用所提供的翼状螺丝将黄铜阀门臂附加到塑料阀门臂上。确保锯齿啮合适当。
- If user experiences any difficulty operating cylinder valve discontinue use and contact supplier. 如果使用者在操作气瓶阀时有困难,需停止使用,并与供应商联系。
- An acetylene cylinder valve should not be opened more than approximately1 1 /2 turns. 乙炔钢瓶阀门不能开启得超过大约11/2圈。
- Always pressurize a regulator slowly, while standing with the cylinder valve between you and the regulator. 总是站得使钢瓶阀门位于你和调整器之间，对调整器慢慢加压。
- Always open a cylinder valve slowly. Never crack open a hydrogen cylinder to clear the valve of dust, as the escaping hydrogen may ignite. 总是慢慢地开启钢瓶阀门。由于溢出的氢可能着火，禁止啪地一声打开氢钢瓶。
- At the end of the shift or work day, close the cylinder valve and bleed the pressure off the regulator and torch equipment. 在下班或工作日结束的时候，关闭钢瓶阀门，放出调整器和吹管设备内的压力。
- Recommended Closing Procedure: Close the cylinder valve tightly using a gloved hand. 推荐的关闭程序：用戴手套的手紧紧地关闭阀门。
- This partition should extend from the top of the panel to18 inches below the cylinder valve. 隔离物应该在钢瓶阀门下面，从控制板顶部伸出来18英寸。
- If user experiences any difficulty operating the cylinder valve, discontinue use and contact supplier. 如果用户在操作钢瓶阀门时遇到任何困难，停止使用，联系供应商。
- Proudly mainly engaged in full range of products Germany, Italy, two-wire hose Granville, CKD cylinder valve. 主要经营德国宝德全系列产品,意大利双威钢丝胶管，CKD汽缸阀门。
- Caution: If user experiences any difficulty operating a cylinder valve, discontinue use and contact supplier. 警告：如果用户在操作钢瓶阀门时遇到任何困难，停止使用，联系供应商。
- They are designed to provide a secondary seal in the event the cylinder valve develops leakage through the valve seat. 它们是设计用来在钢瓶阀门通过阀座产生泄露的情况下提供一个二次密封。
- Always close the cylinder valve when product delivery is not needed. Do not leave it open when the equipment is unattended or not operating. 当不需要产品输出时，总是关闭钢瓶阀门。当设备无人照管或没有运转时，不要让阀门开着。
- Always ensure that cylinder valve is closed, outlet seal is installed gas-tight, and protective cap is in place before shipping. 在运输之前，总是确保钢瓶阀门关闭、排气口密封安装正确和保护帽在正确的位置。
- Leaks occurring at the cylinder valve's pressure relief device, diaphragms, or valve to the cylinder connection cannot be repaired. 发生在钢瓶阀门的减压装置、横膈膜或阀门到钢瓶的接头处的泄露不能维修。
