您要查找的是不是：
- response surface met hodology (RSM) 响应曲面法
- response surface met hodology 响应面
- Fig. 2. A three-dimensional response surface. 图2.;三度空间的反应曲面
- The level at which the ground surface meets the foundation of a building. 参考水准面地表面与建筑物基础相遇的高度
- Therefore, P should be substituted by a response surface for each genotype. 因此，p必须被各个基因型的反应面所代替。
- Optimization of Technology by Response Surface Methodology: Producing Cholesterol Oxidase From Brevibacterium sp. 响应面分析应用于短杆菌产酶工艺的优化。
- The optimum ratio of GE, PE, PC, Vc and CA was 30:60:20:1:2, and it was obtained by response surface methodology. 通过响应面分析法得到了的具有最佳抗氧化性的复合天然抗氧化剂，其各成分比例为30:60:20:1:2。
- In this paper, the optimization design of the transonic airfoil is performed by the Response Surface Methodology(RSM). 基于响应面方法进行了跨声速翼型的气动优化设计。
- A response surface method(RSM) for structure reliability analysis of solid rocket motor(SRM) grain was presented. 发展了一种固体火箭发动机药柱结构可靠度分析的响应面法。
- The technique of extraction of Sargassum polysaccharide was optimized by the method of response surface analysis(RSA). 通过响应面分析法(RSA)优化了马尾藻多糖的提取条件,对关键影响因素的最佳水平范围及其交互作用进行了研究。
- Given a response surface equation in quadratic form, the Six Sigma Black Belt will be able to compute the stationary point. 给出一个二次方程式形式的响应曲面公式，6西格玛黑带应能计算出驻点。
- The projection lines of all the tapered surfaces meet at a common point on the bearing axis. 所有圆锥表面的投影线都在轴承轴线的同一点相聚。
- Ditto for one way ANOVA, two way ANOVA( with and without replicates), full and fractional factorials, and response surface designs. 给定一组数据，6西格玛黑带应能进行一维方差分析、维方差分析（或没有重复）全部析因，部分析因和响应曲面设计。
- The sharp edge or ridge formed by two surfaces meeting at an angle, as in a molding. 尖脊两个平面以某种角度相接所形成的尖突的边或脊形，如铸模中的
- Combining the Plackett-Burman design, response surface analysis andthe steepest ascent method, the static culture media of A. 将Plackett-burman设计、响应面分析和最速增长途径法联用，对A.
- Ditto for one way ANOVA, two way ANOVA (with and without replicates), full and fractional factorials, and response surface designs. 给定一组数据，6西格玛黑带应能进行一维方差分析、二维方差分析（有或没有重复），全部析因，部分析因和响应曲面设计。
- Open the exit to make the eluent flow out till the bed surface meets the liquid surface, shut off the exit. 3.;加样品：打开螺旋夹使柱面上的洗脱液流出，直至床面与液面刚好平齐为止，关闭下端出口。
- The Response Surface Model of FMS is drafted combining the design of experiments, simulation experiments, and analysis of data by this method. 该方法结合实验设计、仿真实验和数据分析，拟合出系统的响应曲面模型。
- The response surface method was used to optimize the culture medium for anti-fungus compound produced by Streptomyces 702 under unsterilized condition. 用响应面分析方法对链霉菌702产抑真菌物质生料发酵培养基进行了研究。
- Bucher C G,Bourgund U.A fast and efficient response surface approach for structural reliability problems[J].Structural Safety,1990,7(1):57-66. 佟晓利赵国藩.;一种与结构可靠度分析几何法相结合的响应面方法[J]
