您要查找的是不是:
- gear pair with reference center distance 标准中心距齿轮副
- reference center distance 标准中心距
- The center distance of R/L crank between piston with cylinder concern the power of engine. 活塞与汽缸的间隙直接影响引擎运转之特性,因此最佳的间隙值会使引擎产生最佳的马力及燃烧的废气。
- One ophthalmologist at a reference center diagnosed and graded these images after receiving them via the Internet. 一个位于中心的眼科医师在藉由网际网路得到这些影像后,对病情进行诊断并对影像结果进行评价。
- Model : Defined by the center distance between shafts. The bigger the model number. The bigger the reducer structure. 型号:由减速机入力和出入之中心距而定,型号越大,减速机体积越大。
- Dies seat: Adopt West Germany technology (Inlay type), assure the drawing center distance to avoid the wire breakage. 模座:采用西德技术(镶入式),保证拉伸的中心距,减少断线机率。
- Ayer Library - Provides a reference center, children's section and policies. Includes meeting room information, hours and location. 易易工作室-各种在线工具,站长网志,以及多个应用项目。
- KT-series is as the same as ZT-series and its principle is adjusting the center distance of roller-sting to welding the weld material of different diameter. KT系列产品与ZT系列产品相同,工作原理是人工调正滚轮架的中心距,以适应不同直径焊接体的焊接。
- When the center distance of two involute gears is fixed, the plane higher pair composed by them will introduce one restriction to the mechanism. 摘要当参与啮合的两个渐开线齿轮之间有固定的中心距时,其构成的平面高副引入一个约束;
- The change of center distance due to non-conjugate of corrugating roller in molding corrugated board process was discussed. 摘要论述了瓦楞辊在成型瓦楞纸板过程中,由于瓦楞辊的齿形是非共轭齿廓,中心距是变动的。
- Ship hull's sagging and hogging may cause center distance increasing or reducing to longitudinally disposed gear housing. 船体中垂及中拱弯曲变形会使沿船体纵向布置的齿轮座中心距产生增减。
- The center distance of the roller on the cradle draft assemble greatly affects the yarn eveness, hairiness and ends breakage. 摘要牵伸装置上罗拉的中心距及其定位对成纱的条干不匀率、毛羽、断头都有较大影响。
- For unknown class label samples set,an unsupervised feature selection algorithm based on center distance ratio principle is proposed. 针对未知类标号的样本集,提出基于中心距离比值准则的无监督特征选择算法。
- Materials are charged out via automated circulation system. The Automated Reference Center contains microcomputer workstations for searching the library's growing collection of databases on CD-ROM. 阅读资料由自动流通系统调出,自动查阅中心备有微机工作站,以供读者根据只读储存器光盘查阅图书馆日益增长的数据资料。
- Calculates the coordinates of the spindle and drive shaft and checking the center distance, determined department spindle must use dislodges the gear. 计算主轴、传动轴的坐标并进行中心距验算,确定部分轴上需采用变位齿轮;
- Verticality of track and wheel should more than 999/1000.The center distance of wheels is 5835mm and the relative difference of it is no more than 1mm. 轮对轨间的不垂直度不得大于1/1000,车轮顺轨中心间距5835mm的相对差值不得大于1mm。
- Don't refer to this matter again, please. 请不要再提这件事了。
- In order to avoid the “midconvex” of tooth profile and the serious abrasion in dedendum, the technology of center distance variation was adopted. 为了避免出现齿面“中凸”及齿根部研磨较严重的现象,采用了变中心距研齿工艺。
- The product output to sprain torque ,which make gears the least load and (with the equal center distance)can inproue more 30% bearing capacity than the traditional load capacity. 本产品为输出升扭,使各档轮所受载荷减小,相同中心距较传统结构提高承载能力30%25以上。
- Few series hae examined this disease in adults.A retrospectie reiew was performed of 95 adults who had MCD and were seen at a single referral center. 在一个单转诊中心进行了一项回顾性调查研究,95例**微小病变肾病患者被列入研究和观察的。