您要查找的是不是：
- The reason the propeller shaft shortens as the angle increases is that the rear axle and differential move in a shorter arc than the propeller shaft. 当角度增加时,传动轴变短的原因是后桥和差速器运动的弧度小于传动轴运动的弧度。
- This accommodates any effective change of length of the propeller shaft as the rear axles move toward or away from the car frame. 当后桥在车架上向前或向上运动时,这种结构足以调整传动轴长度的任何变化。
- "Disconnect the rear axle or the front end of the propeller shaft or the universal joint, according to type. Where needle bearings are used, tape the bearing retainers to the shaft to avoid losing needles." 根据变速器的类型,拆下后桥或者传动轴或者万向节。如使用滚针轴承,应用布带捆住轴承护圈,以避免滚针失落。
- Remove the rear propeller shaft. 拆卸后传动轴。
- front axle propeller shaft 前桥传动轴
- "The propeller shaft is a drive shaft to carry the power from the transmission to the rear-wheel axles. It connects the transmission main, or output, shaft to the differential at the rear axles." 传动轴是将动力从变速器传送到后桥的驱动轴上。传动轴连接变速器的主轴或输出轴,并与后桥上的差速器相连接。
- The rear axle carries the greatest weight. 后轴负荷最重的分量。
- Nothing seems to be wrong with the propeller shaft. 转动轴看来没毛病。
- Reindex propeller shaft 180° and evaluate. 将传动轴翻转180°，并测试。
- A pole connecting the rear axle of a vehicle with the front. 连接杆连接车辆前后轴的杆
- Han Yingchun, Wang Xueming, Chen Yubao. The new technology of the forward extrusion and cross rolling for the rear axle shaft sleeve of light truck. Germany： 6th ICTP, 1999. 韩英淳;王学明;陈义宝等.;“农用运输车正挤与横轧式后桥半轴套管”发明专利
- Front axle moved forward 60mm, rear axle moved backwards 20mm. 前桥前移 60 厚米，后桥后移 20 毫米。
- The engine acts as the power unit located normally at the front of the car,followed immediately by a cluth,gear box ,propeller shaft,universal joint,differential,back axle,ect. 发动机作为动力装置通常位于在车子的前面,然后立刻由齿轮,齿轮箱、传动轴万向节、鉴别、,后车轴等。
- Aligning intermediate shaft and propeller shaft after launching. 下水后中间轴和螺旋桨连接后校中。
- This measurement will give you the propeller shaft angle (C). 测量结果就是传动轴工作角（c）。
- The rear axle is stationary, and is bolted rigidly to the main frame. 后轴是固定的，用螺栓刚性固定在主机架上。
- Measuring clearance between propeller shaft &bearing. 螺旋桨轴与轴承间隙测量。
- Aiming at laggard and low automatization degree of clearance measure method on axial assembly clearance between half shaft assembly and rear axle housing in automotive rear axle assembly, a new type clearanceometer was developed. 针对汽车后桥总成中半轴总成与后桥壳之间轴向装配间隙测量方法落后、动化程度差等问题,开发了汽车后桥总成装配间隙测量仪。
- Different nacelle with deeper ross-section and intake over propeller shaft. 发动机舱、螺旋桨轴处的进气口有一些不同。
- Install the straps and bolts to hold the propeller shaft to the yoke. 安装扣夹和螺栓，将传动轴固定到轴轭上。
