您要查找的是不是:
- The first and second contact pads have an asymmetrical configuration, which may have different ratios of length to width. 第一接触焊盘和第二接触焊盘具有非对称结构,其可具有不同的长宽比。
- Application Range of the Deflection Formula of Rectangular Plate with Large Ratio of Length to Width and Fixed Boundary 周边固定大长宽比矩形薄板挠度计算公式的应用范围
- Experimental study on ratio of length to width of surviving random adipofascial flap 随意型筋膜皮下组织瓣成活长宽比实验观察
- Experiment Study and Calculation formulae of Rectangular Plate Deflection with Large Ratio of Length to Width and Fixed Boundary 周边固定大长宽比矩形薄板挠度的实验研究与计算公式
- ratio of length to width 长宽比
- The ratio of its length to width was much larger than any similar contemporary structure. 它的长宽比大大超过了同时代的任何类似的建筑物。
- It was showed that the palisade cells of the hardy vareties have higher value of length to width ratio and more chioroplarts and mito chondsia. 利用电导法测定各品种之间的抗寒性与组织解剖观察结果一致。
- But the ratio of height to width is at work. 增大框筒的高宽比可以减小相同高度比例处的剪力滞后效应。
- Length to diameter ratio of flexspline. 柔轮长度与内径之比。
- The ratios of the length to width of the propodus of the fourth leg in the three kinds of mitten crabs were identical or near to those of taxonomic samples. 三种绒螯蟹的第四步足前节长宽比值,与其分类标本吻合或基本吻合。
- The question about the seals of high speed churn shaft with large ratio of length to diameter is one of the difficult problems. 高速大长径比搅拌轴密封可靠性问题,一直是从事密封工作者探索的问题之一。
- Isolators with different ratio of length to height (L/H) and divergence angle were investigated and the influence of back pressure on location of the shock train was analyzed. 在来流马赫数2.;3条件下,通过改变不同的反压来研究反压对不同长高比等截面隔离段和带扩张角隔离段激波串起始位置的影响。
- The results showed that the image analysis method can obtain the average value and distribution curve of ratio of length to diameter for vilnite powder with needle shape. 研究表明图像分析方法可以直接给出硅灰石针状粉末的平均长径比及不同长径比的分布情况。
- unequal scale of length to width 非等比长宽
- Discussed thoroughly the extrusion swell phenomenon and mechanism of polymer melts in conical die with different entrance angles and different ratios of length to diameter. 深入讨论了聚合物熔体在不同长径比、不同角度圆锥口模的挤出胀大现象及机理。
- the tube with large ratio of length to diameter 细长管
- steel fiber ratio of length to diameter 钢纤维长径比
- ratio of length to diameter for the mold 模具长径比
- The miter limit is the maximum allowed ratio of miter length to stroke width. 斜接限制是指斜接长度与笔划宽度之间的所允许的最大比值。
- The result reveals that small geometric focal length and large angle may decrease the -3dB focal area, and increase length to width ratio and the pressure magnitude of main lobe. 由结果得知,曲率半径愈小张角愈大会导致烧灼面积减小、长宽比增加以及压力主峰值的提高。