您要查找的是不是:
- Compressing moulding presses.., hot press... 就是液压机什么得。。。
- A new type BN ceramic material is made by hot pressing(HP) method. 采用热压(HP)法制备了BN陶瓷材料。
- The powder can be directly consolidated into blocks via hot pressing. 这些粉末可以通过热压形成整块。
- At the polyalkene Oct.1999, after the injection molding, hot press as molding. 一般以聚烯烃为主要原材料,经过注塑、热压等工艺加工成型。
- Two hot pressing shaped, Ms. Man face, schoolbags sandwich, mainly Middle Eastern countries and regions. 两次热压成型、奥古曼面、意杨夹心、主要针对中东国家和地区。
- The polycrystalline Na-Bata-Al_2O_3 with relative density greater than 99% has been prepared by means of hot pressing. 用热压的方法可制得相对密度大于99%25的Na-Beta-Al_2O_3。
- Rapid hot backup of data and system is performed by use of highspeed connection between STANDBY server and master server to make system work continuously as master server damaged accidentally. 利用STANDBY服务器与主服务器间的高速连接 ,进行数据及系统的快速热备份 ,使系统在主服务器意外损坏的情况下能继续工作 ;
- Ti2AlC bulk material was synthesized by hot pressing using elemental powder mixture of Ti,Al and active carbon. 以Ti、Al元素粉和活性炭为原料,采用热压工艺合成了Ti2AlC块体材料。
- TiB2-Al2O3 Multiphase ceramics with Y2O3-La2O3 as sintering aids are fabricated by hot pressing. 本文以Y2O3-La2O3为烧结助剂,通过热压烧结制备了TiB2-Al2O3复相陶瓷,研究了原料组成对材料的显微结构和力学性能的影响。
- The monoclinic celsian phase in the matrix was produced in situ,during hot pressing,from amphosous BAS. 在热压期间,基体中的单斜相钡长石由玻璃态钡长石原位转变生成。
- This article describes a hot pressing formation technology to make flanged openings on special jacketed vessel shells. 介绍在特殊夹层压力容器制造中对夹层壳体壁上进行开孔翻边热冲压成形的工艺技术。
- In this paper the porous materials were manufactured by PCH comparing with hot pressing (HP). 本文采用的导电金属和不导电陶瓷材料的球形颗粒作为原料,研究脉冲大电流加热条件下颈部的生长模型及原子扩散过程,弄清脉冲大电流加热条件下原子扩散与热压(HP)条件下原子扩散的区别,以证实特殊的电场和磁场是否对原子的扩散具有推动作用,揭示脉冲大电流加热条件下原子的扩散过程。
- Calendaring is glazing technology in coloured light oil and hot pressing two generating units. 压光是上光工艺在涂上光油和热压两个机组上进行。
- PP/straw composites are fabricated by hot pressing, with PP as matrix and wheat straw as the reinforcing agent. 以聚丙烯(PP)为基体,以农作物秸秆(麦杆)为增强剂,用热压成型的方法制备了PP/秸秆复合材料。
- The composite dielectrics mainly composed of PTFE,ceramics and glassfibers are prepared by hot pressing. 采用热压工艺制得聚四氟乙烯/陶瓷/玻璃纤维复合介质材料。
- Hot Pressing was used in preparing the nano-graphite/Al matrix composite material because of the big wetting angle between the graphite and aluminum. 由于铝和碳几乎不润湿,采用热压方法制备纳米石墨/铝基复合材料,并对样品进行热挤压以减少孔隙。
- The results show that the density is the most notable factor,and hot pressing temperature and dose of bagasse are secondary. 试验结果表明:速生杨木/甘蔗渣重组材的密度是最显著性的影响因素,其次为热压温度和甘蔗渣加量。
- The sniper snapped off six rapid shots. 狙击手迅速地连放了六枪。
- Childhood is a period of rapid growth. 幼年是生长迅速的时期。
- The factors are hot pressing temperature, glue spread, BL-formaldehyde absorptive reagent spread and hot pressing time in influence sequence. 影响大小次序是热压温度>脲胶施加量>BL-甲醛消纳剂施加量>热压时间。