您要查找的是不是:
- pure shear strain 纯剪应变
- This verifies the equivalence of pure shear and simple shear. 这就证明了线剪切与简单剪刀的等价性。
- Objective. To investigate intradiscal pressure, shear strain between anulus and adjacent endplates, and fiber strain in the anulus under pure and combined moments. 目标:调查在环与相邻终板之间的盘内压和切应力,以及单纯和联合运动时的纤维强度。
- The shear strain can be determined in the following way. 用下列方法能够确定切应变。
- ECAP is an effective method realizing pure shear deformation. ECAP是实现材料纯剪切变形的有效方法。
- Objectie. To inestigate intradiscal pressure, shear strain between anulus and adjacent endplates, and fiber strain in the anulus under pure and combined moments. 目标:调查在环与相邻终板之间的盘内压和切应力,以及单纯和联合运动时的纤维强度。
- Shear strain in MBE grown CdTe films on Si(211) substrates[J]. 引用该论文 王元樟;陈路;巫艳;吴俊;于梅芳;方维政;何力.
- The transformation is due to the shear strain imposed on the specimen by ECAP. 该转变发生是由于ECAP过程中材料承受剪切应变,应变能累积诱发再结晶,从而形成等轴晶双相结构。
- The only strain is a shear strain and the dilatation is zero, these waves are called shear waves. 唯一的应变是剪应变而没有膨胀,这种波叫剪切波。
- The S-waves have the kinematics of pure shear waves,thus we can pick their first arrivals,calculate their interval velocities,and further compu. 实验发现:裂缝密度较高时,可以观测到明显的横波分裂现象;而裂缝密度较低时,仅能观测到微小的速度异常。
- Good bonds are always accompanied by surface extension, that is, plastic shear strain. 良好的键合总伴有表面延伸即塑性切向形变。
- Natural deformational zones are commonly the result of general shear, a combination of pure shear (coaxial contraction or extension) and simple shear. 天然变形带通常是一般剪切作用的产物,是纯剪切(共轴缩短或伸展)和简单剪切的组合。
- During extensional activities of Late Cretaceous to Eogene, intense upwelling of asthenosphere happened under the fault zone, leading to lithospheric necking in pure shear model. 断裂带在晚白垩世-早第三纪的伸展活动中,软流圈发生了强烈的上隆,岩石圈出现了显著的细颈化,属于纯剪切伸展模式。
- Variation of Damping Properties Under Magnetic Field and Shear Strain Amplitude in Fe-Cr-Al Alloys. 高阻尼Fe-Cr-Al合金在磁场和应力场下的阻尼行为
- Meanwhile, under both pure shear loading, the percentages of the sagittal and the transversal components are increased with the decrease of the sagittal angle. 前剪和后剪载荷条件下,关节突接触力的矢状和水平分力均随关节突矢状方向角度的减小而增大。
- The elasticity of copolyester increases with the shear strain but decreases with the temperature. 弹性随切应力的增大而增大,随温度的升高而降低。
- The results show a certain time thermal cycle can cause the fracture mechanism change.It varies from original pure shear fracture to microvoid coalescence fracture gradually. 结果表明,一定时间的热循环会造成LF6铝合金焊接接头断裂机理的改变,由未经热循环时的纯剪切型断裂,逐渐过渡成微孔聚集型断裂。
- The kinematic vorticity is a measure of the non-coaxiality in progressive deformation history and,therefore,is the ratio of the pure shear to simple shear of a general shear zone. 本文对一般剪切带的概念及其分类进行了描述,对运动学涡度和极摩尔圆的原理及其应用进行了系统的论述,并在此基础上提出了几种新的实用的极摩尔圆编制方法。
- The residual strain is the additional shear strain created with the increase of pore pressure due to cyclic shear under initial shear stress. 残余应变是由于周期剪切引起孔隙压力增长;在初始剪力作用下产生的附加的剪应变.
- Notably, we proceeded a series of pure shear stress tests in order to isolate the influence of volumetric stress and shear stress to the volumetric behavior. 藉由一系列三轴试验之结果,希冀对木山层砂岩在遇水时力学行为之变化有进一步认知。