您要查找的是不是：
- Satisfactory service record and an external examination of the inboard and outboard propeller shaft assemblies togather with the bearing wear down check at the end of the normal survey period. 海水润滑式之艉轴检验延期，延期不超过一年（仅可延期一次）其检验范围：
- propeller shaft assembly 螺旋桨轴总成
- Nothing seems to be wrong with the propeller shaft. 转动轴看来没毛病。
- Reindex propeller shaft 180° and evaluate. 将传动轴翻转180°，并测试。
- Remove the rear propeller shaft. 拆卸后传动轴。
- Aligning intermediate shaft and propeller shaft after launching. 下水后中间轴和螺旋桨连接后校中。
- This measurement will give you the propeller shaft angle (C). 测量结果就是传动轴工作角（c）。
- Measuring clearance between propeller shaft &bearing. 螺旋桨轴与轴承间隙测量。
- Different nacelle with deeper ross-section and intake over propeller shaft. 发动机舱、螺旋桨轴处的进气口有一些不同。
- Install the straps and bolts to hold the propeller shaft to the yoke. 安装扣夹和螺栓，将传动轴固定到轴轭上。
- The gear and rack type bus redirector is consisted of a turning spindle and cylinder assembly, a transmission shaft assembly, and a redirector assembly. 齿轮齿条式汽车转向器是由“转向轴及柱管总成”、“转向传动轴总成”、“转向器总成”三大总成组成。
- One-piece solid stainless steel dynamically Balanced rotor/pump shaft assembly with short shaft overhang - specifically designed for submersible pump application. 一体式实心不锈钢动态平衡转子/泵轴以悬挂短轴方式安装,这是专为潜水泵的特殊应用进行的特殊设计。
- Align previously made marks on yoke and propeller shaft and install propeller shaft. 将定位轭架上的预制标记对准传动轴并安装传动轴。
- Mark the propeller shaft and pinion yoke, or pinion flange, for installation reference. 在传动轴和传动轴轴轭、或小齿轮轴轭上作标记，作安装的参考标志。
- Align the installation reference marks on the propeller shaft and yoke and install the propeller shaft. 对准传动轴和轭上安装参考标记，安装传递轴。
- The reason the propeller shaft shortens as the angle increases is that the rear axle and differential move in a shorter arc than the propeller shaft. 当角度增加时,传动轴变短的原因是后桥和差速器运动的弧度小于传动轴运动的弧度。
- Aiming at laggard and low automatization degree of clearance measure method on axial assembly clearance between half shaft assembly and rear axle housing in automotive rear axle assembly, a new type clearanceometer was developed. 针对汽车后桥总成中半轴总成与后桥壳之间轴向装配间隙测量方法落后、动化程度差等问题,开发了汽车后桥总成装配间隙测量仪。
- This accommodates any effective change of length of the propeller shaft as the rear axles move toward or away from the car frame. 当后桥在车架上向前或向上运动时,这种结构足以调整传动轴长度的任何变化。
- Based on the research of the structure of arrester and bolts in axle shaft assembly, the author gives a floating structure, with which we can directly press the components on the dolly. 在研究半轴总成制动器及过渡接盘螺栓结构的基础上,提出了一种可以在线体小车上直接压装元件的浮动支承结构。
- The D9B can be equipped with a power take-off designed for propeller shaft operation or direct-mounted hydraulic pumps. D9B可提供适用于驱动轴运转或直接安装式液压泵的动力输出。
