您要查找的是不是：
- propeller shaft slip 螺旋桨轴伸缩节
- propeller shaft slip joint 传动轴滑动接头
- Nothing seems to be wrong with the propeller shaft. 转动轴看来没毛病。
- Reindex propeller shaft 180° and evaluate. 将传动轴翻转180°，并测试。
- Remove the rear propeller shaft. 拆卸后传动轴。
- Other goodies include a new limited slip differential, a final drive ratio of 3.71:1, and an alloy torque tube with a lightweight carbon-fiber propeller shaft. 其他的物品，包括一个新的限滑差速器，最终传动比的3.;71:1，和扭矩合金管轻质碳纤维传动轴
- Aligning intermediate shaft and propeller shaft after launching. 下水后中间轴和螺旋桨连接后校中。
- This measurement will give you the propeller shaft angle (C). 测量结果就是传动轴工作角（c）。
- Measuring clearance between propeller shaft &bearing. 螺旋桨轴与轴承间隙测量。
- There must be one or more universal joints to permit variations in the angle of drive. There must also be a slip joint that permits the effective length of the propeller shaft to change. 一个或几个万向节来适应传动角度的变化;一套伸缩花键,能够改变传动轴的现有长度。
- Different nacelle with deeper ross-section and intake over propeller shaft. 发动机舱、螺旋桨轴处的进气口有一些不同。
- Install the straps and bolts to hold the propeller shaft to the yoke. 安装扣夹和螺栓，将传动轴固定到轴轭上。
- Align previously made marks on yoke and propeller shaft and install propeller shaft. 将定位轭架上的预制标记对准传动轴并安装传动轴。
- Mark the propeller shaft and pinion yoke, or pinion flange, for installation reference. 在传动轴和传动轴轴轭、或小齿轮轴轭上作标记，作安装的参考标志。
- Align the installation reference marks on the propeller shaft and yoke and install the propeller shaft. 对准传动轴和轭上安装参考标记，安装传递轴。
- The reason the propeller shaft shortens as the angle increases is that the rear axle and differential move in a shorter arc than the propeller shaft. 当角度增加时,传动轴变短的原因是后桥和差速器运动的弧度小于传动轴运动的弧度。
- This accommodates any effective change of length of the propeller shaft as the rear axles move toward or away from the car frame. 当后桥在车架上向前或向上运动时,这种结构足以调整传动轴长度的任何变化。
- The D9B can be equipped with a power take-off designed for propeller shaft operation or direct-mounted hydraulic pumps. D9B可提供适用于驱动轴运转或直接安装式液压泵的动力输出。
- The propeller shaft to be turned clockwise viewed from afterward of M/E when running ahead. 当主机正车时，从主机后面看螺旋桨轴为顺时针旋转。
- "The propeller shaft may be solid or hollow, protected by an outer tube or exposed. 传动轴可以是实心的或空心的,由套管加以保护或裸露在外。
- 今日热词
-
- 深远海浮式风电平台 - deep-sea floating wind power platform
-
- 京雄高速公路 - Beijing-Xiongan expressway
-
- 农业及相关产业增加值 - the added value of agriculture and related industries
