您要查找的是不是：
- Adjust processing temperature according as the extruder screw. 根据挤出机大小及其螺杆塑化能力适当调整加工温度。
- These are the basis of studyi ng critical processing temperature for propellants. 这些可以作为研究火药工艺温度的基础。
- Methods To test with HP-5 capillary chromatogram clumn,by using FPD tester,through processing temperature rising. 方法以HP-5毛细管色谱柱,用FPD检测器,通过程序升温进行检测。
- The roasting time and process temperature also play important roles in the roast processing and chromium leaching. 合适的焙烧温度和焙烧时间对焙烧过程的进行和提高铬的溶出率有很重要的作用。
- The formation of acrylamide in food is influenced mainly by the content of reducing sugars or asparagine in materials and the processing temperature. 原料中还原糖、天冬酰胺含量及加工温度是影响食品中丙烯酰胺形成的主要因素。
- The effects of processing temperature and PMMA content on the micromorphological structure and mechanical properties of the PPS composite were studied. 考察了加工温度及PMMA用量对聚苯硫醚复合材料微观形态结构和力学性能的影响。
- One method to improve fluid flow without compromising product quality wou ld be to confine process temperature in creases to around the evaporator outlet. 一种能改善磷脂流动性又不损害磷脂质量的方法是提高浓缩器出口范围的温度。
- It was found that at the higher screw speed, the higher draw rate and the lower processing temperature the PA6 fibrils were finer and the mechanical properties of PP/PA6 compos... 发现当螺杆转速越高、牵引速率越快、加工温度越低，分散的PA6纤维尺寸越小，复合材料的力学性能越好。
- The flowing curve of PHBV was fluctuated greatly with the influence of the processing temperature and resident time.When the equipment of melting spinning... 在对现有熔融纺丝成形设备适当改造后;通过严格控制纺丝成形工艺条件;可纺制出力学性能满足美国药典要求的PHBV长丝.
- The results show that the processing temperature is become low, resin flowability and product, surface quality are improved,and the graft ratio is increased. 实验表明:用该加工改性剂可以降低加工温度,提高树脂流动性,改善制品外观质量,提高正品率。
- We consider your response inadequate in that you provide no information relating to the impact that increasing the process temperature would have on the product. 你们在答复中没有提供关于工艺中温度的提高对产品有什么影响方面的资料，我们认为你们的答复不充分。
- This article analyses the present status of normalizing furnace of Wuyang,the effect of process temperature,furnace atmosphere,etc.on bottom roller and normalizing roller mark. 本文剖析了舞钢常化炉现状、工艺温度、炉内气氛等对炉底辊的影响以及常化辊印的产生;制定了措施;减少常化辊印.
- Some factors affecting the pepsin digestibility of fishmeal such as storage time, processing temperature, fat, and amino content were discussed in this thesis and the further study was also discussed. 本文讨论了原料鱼的新鲜度、鱼粉生产工艺、贮藏时间、脂肪含量、氨基酸组成等对鱼粉胃蛋白酶消化率的影响，并对本研究的进一步工作做了讨论。
- In this paper, the effects of processing temperature,acidify and alkalinity, sodium chloride and accharose, and four metal cations on the stability of the pigment of Basel-la rubra L. are reported . 本文以藤菜鲜果为原料,用藤菜鲜果的稀水溶液为研究对象,对藤菜紫色素在不同PH介质、不同温度及光照条件下的稳定性进行了研究,并讨论了若干金属离子及食盐和蔗糖对该色素的影响。
- OBJECTIVE To determine the structure of gypsum crystal from different processing temperatures. 目的鉴定不同炮制温度下的石膏晶形结构。
- It was found that at the higher screw speed, the higher draw rate and the lower processing temperature the PA6 fibrils were finer and the mechanical properties of PP/PA6 composites were better. 发现当螺杆转速越高、牵引速率越快、加工温度越低,分散的PA6纤维尺寸越小，复合材料的力学性能越好。
- It was employed that changing the processing temperature, screw speed and draw rate in order to study how PP/PA6 in-situ fibrillation composite was affected by the processing conditions. 在PP/PA6共混物的挤出加工中分别调整加工温度、挤出机螺杆转速、牵引速率，得到不同加工条件下的PP/PA6原位成纤复合材料。
- The effect of processing temperature on morphology and permeability to organic solvent of ultraviolet(UV) irradiated HDPE/PA6 blend was studied through SEM and toluene permeability test. 采用SEM和对甲苯渗透性的测试研究了紫外线辐照高密度聚乙烯／尼龙6（HDPE／PA6）共混物的成型工艺、形态结构以及对有机溶剂的阻隔性能。
- The results shows that the process aid LA-D could improved the plasticizing homogencity,flow and decreased the processing temperature,and also enhance the quality of the plastic products. 研究表明,LA-D加工助剂能改进加工成型时的塑化均匀性、流动性,降低加工温度,提高制品的质量。
- The Kraft process produces pulp with longer fibers, while sulfite pulp, using lower process temperatures, produces more white pulp with shorter fibers. 牛皮纸工艺生产的纸浆纤维较长，但亚硫酸盐纸浆用较低处理温度生产的纸浆色泽较白纤维较短。
