您要查找的是不是：
- printable polypropylene film 可印刷的聚丙烯膜
- Polypropylene film as medium, and aluminum foil as electrode. 聚丙烯薄膜作介质，铝箔作电极。
- Non-inductively wound with metallized polypropylene film. 金属化聚丙烯作介质，无感式卷绕。
- Polyester film or polypropylene film as medium and aluminum foil as electrode. 采用聚酯、聚丙烯薄膜作介质，铝箔作电极。
- Structure: With polypropylene film as dielectric, AL foil as electrode, foil-exposed construction, unidirectional lead, epoxy resin dip sealed. 结构：采用聚丙烯作介质，铝箔作电极，露箔式结构，单向引线，环氧树脂包封。
- PPN are non-indectively woud with Polypropylene film dielectric and aluminum foil electrodewith copper-clad steel leads and are epoxy resin coated. PPN无电感性，用聚丙烯膜介质和铝箔绕制，用铜覆盖钢引线作电极，用环氧树脂作外包装。
- CBB60 metallized polypropylene film capacitor is used as a motor starting capacitor or a motor running capacitor in 50HZ AC singlephase motors. CBB60型金属化聚丙烯电容器可用于频率为50Hz的交流电源供电的单向电动机的动起和运转。
- CBB61 metallized polypropylene film capacitor is used as a motor starting capacitor or a motor running capacitor in 50HZ AC singlephase motors. CBB61型金属化聚丙烯电容器可用于频率为50Hz的交流电源供电的单向电动机的运转和运转。
- CBB21 are non-inductively wound with metallized polypropylene film as the dielectric/electrode with copper-clad steel leads and epoxy resin coating. CBB21为无感结构，用金属化聚丙烯膜作为电介质／电极绕制而成，导线采用镀锡铜包钢线，使用环氧树脂包封。
- Name: not ordinary oriented polypropylene film (CPG) of low-temperature Refeng-oriented polypropylene film (CPL) in the cooking temperature of polypropylene film (CPR). 名称：普通未拉伸聚丙烯薄膜（CPG）低温热封型未拉伸聚丙烯薄膜（CPL）中温蒸煮聚丙烯薄膜（CPR）
- Test Method of Wetting Tension of Polyethylene and Polypropylene Films (08. 聚乙烯和聚丙烯薄膜的湿润张力的试验方法(08。
- CBB81 are non-inductively wound with polypropylene film as the dielectric and aluminum foil as the electrode with copper-clad steel leads and epoxy resin coated. CBB81为无感结构，用聚丙烯膜作为电介质和铝箔为电极卷绕而成，导线采用镀锡铜包钢线，使用环氧树脂包封。
- Table 1 is polyethylene and polypropylene films to a performance comparison. 表1是聚乙烯和聚丙烯薄膜性能上的比较。
- CBB80 are non-inductively wound with metallized polypropylene film as the dielectric/electrode with encapsulated in a plastic case sealed with epoxy resin. CBB80为无感结构,用高温金属化聚丙烯膜为电介质/电极卷绕而成,使用环氧树脂密封在塑料壳中。
- CBB20 are non-inductively wound with metallized polypropylene film as the dielectric/electrode and copper-clad steel leads and outer wrapping of polyester sealed with epoxy resin. CBB20为无感结构，用金属化聚丙烯膜为电介质／电极绕制而成，导线采用镀锡铜包钢线或铜线，外层采用聚酯胶带包裹，两端用环氧树脂密封。
- The interelectrode dielectric adopts the polypropylene film with surface coarsening which is easy to impregnate so as to enhance the reliability of high-capacity capacitor. 极间介质为易于浸渍的表面粗化聚丙薄膜，特别提高了大容量电容器的可靠性。
- The determination of Pb,Cd and Hg in the metalized polypropylene film dielectric capacitor by theatomic absorption spectrophotometry(AAS) has been discussed. 探讨了用原子吸收光谱仪测定金属化聚丙烯膜电容器中铅、镉及汞含量的方法。
- CHANG Xian-min,WANG You-gong,LI Li-qin.The effect of interplay between impregnant and film to the performance of polypropylene film[J].Power Capacitor,1985,3(6):1-6. [5]常宪民;王友功;李丽琴.;油-膜相互作用对聚丙烯薄膜击穿性能的影响[J]
- The article is too badly written to be printable. 这篇文章写得很糟糕，不宜发表。
- That was infinitely better than his last film. 这比他上一部电影不知胜过多少倍。
