您要查找的是不是:
- The shaving stock of preshaving gears has direct influence on the shaving effect and the tooth profile of preshaving cutters. 剃前齿轮的留剃量形式直接影响剃齿效果及剃前刀具齿形。
- The algorithm and formulas to determine the size of tip relief modification of pre shaving gear hobs are put forward.A principle to determine the lead width of tooth roots is also presented. 给出了剃前齿轮滚刀修缘尺寸的计算方法和计算公式,并对滚刀齿根的齿间槽宽提出了更为合理的判断原则。
- We are able to offer the tooth profile of chain and sprocket. 我们有能力提供各种形链和链轮。
- Research on the tooth profile error of gear shaving 剃齿加工齿形误差的研究
- The equations of thecurvature,curvature radius on hypocycloid"s tooth profile are deduced. 在此基础上分析推导了各种型式的滚子链谐波传动的传动比计算公式。
- It is proofed with experiment that these is local sunken point in th e raised tooth profile of involute gear. 试验验证渐开线齿轮凸齿形上确实存在局部凹状。
- This paper discussed the relationship between the involute pitch of tooth root and tooth profile involute in hobbing. 本文阐述了滚刀滚齿时齿轮齿根过渡曲线的延长渐开线的等距线与齿轮齿形渐开线的关系。
- Green People Pre Shave Face Wash 英之绿有机男士果润剃须前洁面啫喱
- Based on the tooth profile curve equation of inner rotors in cycloidal pump, the formula for displacement calculation of the pump are derived. 根据摆线泵内转子的齿廓曲线方程,推导出了摆线泵的排量计算公式。
- At last, the tooth profile is measured and the errors in tooth profile and aptness are evaluated by three coordinate measurement machine. 最后,利用三坐标测量机对进行仿真的锥齿轮廓面进行了测量,并评定了齿轮的齿形和接触迹误差,同时进行了齿轮副接触区域的运转实验。
- During ausform finishing process of hardened gears, there is plastic displacement of metal on the tooth surface and the distortion of tooth profile . 在齿轮热滚挤加工中,轮齿上的金属在强制挤压力的作用下沿齿面产生塑性流动,使齿形发生变化。
- Chamfering process of gear tooth profile and its function are introduced. By tooth profile chamfer, noise of gear transmission can be reduced. 通过对齿轮传动噪声产生原因的分析,介绍运用齿轮倒棱工艺,降低噪声的工艺方法及应用。
- Finally, the dissertation gave a modification method to cycloidal tooth profile, which can change the engaging position and decrease the efficiency. 最后给出了一种针对摆线齿形的修形方法,通过此种修形可以根据需要改变摆线针轮的啮合位置,适当降低效率,从而改善座椅调角器自锁性能。
- Meanwhile obtained the tooth profile equation of pin-track by the tooth profile normal law which matched the inviolate-cycloid compound gear. 同时利用齿廓法线法得出与该复合齿轮相配套的销轨齿廓方程。
- The tooth profile of this kind of gear was composed of two stepped involutes and a joining trasitional curve between them and formed a ladder shape. 这种齿轮的齿廓由两级渐开线和连接它们的过渡曲线组成,形成阶梯形。
- This paper investigated the tooth profile determination, parameterselection and structure design of hobs for machining arc planet aears. gears. 探讨了加工圆弧行星轮滚刀的齿形确定、参数选择及结构设计。
- In order to avoid the “midconvex” of tooth profile and the serious abrasion in dedendum, the technology of center distance variation was adopted. 为了避免出现齿面“中凸”及齿根部研磨较严重的现象,采用了变中心距研齿工艺。
- This essay analyzes and discusses the shaving speed, cutting condition of shaving teeth and chip room model, adopts the different selection and design for main data of shaving cutter in group method during design. 主要对剃齿时的剃齿速度、剃齿切削工况、容屑槽槽型进行了分析和论述,在剃齿刀设计中用分组的方法,对剃齿刀主要参数进行了不同的选择设计,对其产生的效果作了对比分析。
- According to the curves and equations of the speed, acceleration and displacement about the pallet car given in this paper, the actual tooth profile equation had been presented. 根据台车进行变加速运动的速度、加速度和位移曲线,推导出了实际齿廓方程。
- Terauchi, Y., Nagamura, k., Saijo, H., “On surface durability of Involute-cycloid Composite Tooth Profile Gear”,Bulletin of the JSME, Vol.25,No.202. pp.687-695,1982. 罗文国,渐开线直齿锥形齿轮齿根应力计算模式之初步研究,国立中央大学机械工程学系,2005。