您要查找的是不是：
- PLATING THICKNESS MUST BE HELD ON THIS SURFACE. 此表面的镀层厚度应该控制好。
- Can all these apparent indications of plate thickness really be mistaken? 所有这些关于板块厚度的明显标志有可能弄错吗?
- The results showed that measure-control precision of the system is high and the coherence of multi-cylinder liners plating thickness is higher. 试验结果表明，该系统测控精度高，多缸套电镀层厚度尺寸的一致性好。
- For the increasing of plating thickness in electroplating process offered the extensive residual stress to mitigate or promote the Sn whisker. 在不同温度时效处理下，其结果显示锡须晶的数量与长度皆会随著温度的增加而减缓。
- This means that inferences regarding the depth extent of such anomalies are no measure of plate thickness. 这意味着关于这种异常深度范围的推测并不能测定板块的厚度。
- Plating method, Cylinder or MATTHEWS, depends on customer request, printing plate thickness could be appointed by customer. 圆柱卷版方式或欧式matthews装版方式，可依客户要求制作。
- Notice first that there could be a substantial difference between lithosphere thickness and plate thickness. 首先要注意：岩石圈厚度和板块厚度之间可能有重要区别。
- That is, underlay thickness = sinking groove depth + height difference-a printing plate thickness. 即：垫衬厚量=下沉槽广量+低量不差-印版厚量。
- The cross-section of bump is like mushroom, and it is formed when the electroplating plate thickness is higher than the photo resister. 断面形状像茸状的bump。镀层电镀得比电镀光阻的厚度高而形成的。
- An intelligent coated plate thickness measurement system based on a semiconductor laser diode as light source and a CMOS image sensor is introduced. 介绍了一种以半导体激光器为光源，以新型CMOS面阵图象转换器件为传感器的智能型覆铜板测厚系统。
- Hobber and handlethe groove depth and height difference and pillow and a printing plate thickness and underlay between and equal. 下沉槽广量及滚枕低量不差之和与印版厚量及垫衬厚量之和不等。
- Sinking groove depth and height difference on the pillow hobber minus a printing plate thickness, the result is the thickness of the underlay. 下沉槽广量加上滚枕低量不差再加去印版厚量，其甘休即为垫衬厚量。
- Finiteness of the plate thickness causes a variety of failure mechanisms to occur, and qualitative features of the associated stress and strain fields may be deduced. 我们藉由研究分析此地震带的地震活动性与震源机制和应力场变化，以求瞭解此区域的地震活动与地体构造的关系。
- Allow plate thickness and standard deviation shall meet the requirements for their products. Beam deviation should be allowed to meet the size and specifications of their products standards. 钢板厚度及允许偏差应符合其产品标准的要求。型钢的规格尺寸及允许偏差应符合其产品标准的要求。
- The main factors influencing the specific energy by weight included current density, plate thickness, active material structure, the conductivity of active material, grids, electrolyte volume and density. 影响铅酸电池活性物质利用率的主要因素有：电流密度、极板厚度、活性物质的结构、活性物质和板栅的导电性能及电解液的体积和密度等。
- Calculated results showed that the deformation of the composite girder is distributed nonlinearly along its length, and decreases with increasing connection stiffness and steel plate thickness. 计算结果表明，组合梁的变形沿梁长呈非线性分布，随着连接刚度增加而减小，随着钢板厚度的增加而减小。
- And more, with the increase of the heat input, the weld shape change from “nail” shape or “Roemer” shape to “H” shape, and the temperature difference along the plate thickness reduce. 焊缝形状由“钉子”形或“酒杯”形变为“H”形，厚度方向的温差变小；
- He only put a bit on his plate to make fashion. 他只是拨了一点食物到盘子里做做样子。
- The plating is beginning to wear off in places. 镀层有的地方已经磨掉了。
- Max plate thickness of drilling hole 最大钻孔板厚
