您要查找的是不是:
- plastic buckling load 塑料弯曲载荷
- Delaminations may reduce the buckling load of the laminated structure greatly. 脱层的存在将会大大降低层合结构的屈曲载荷。
- The dynamic plastic buckling of earth penetrating weapon(EPW) was experimentally studied. 摘要利用金属靶开展动能深侵彻弹的穿甲屈曲实验研究。
- Buckling loads: Assigned the best buckling curve. 抗弯荷载:选定最佳的抗弯曲线。
- The buckling in static and dynamic compression tests is in inelastic region, it is plastic buckling. 静态以及动态下之挫曲皆已进入非弹性范围,属于塑性挫曲。
- The paper systematically summarizes the paradox in plastic buckling of plates and shells and its research progress overpast decades, and discusses various theories on the paradox. 摘要 本文详细论述了板壳塑性屈曲中的佯谬及其研究进展。并对现有的各种观点作了分析讨论。
- The result showed that slipping of faying surfaces occurred earlier when using thinner splice plates, and the plastic buckling deformation was also greater. 结果表明:采用较薄的拼接板时,试件的拼接区滑移出现得早,拼接板的塑性屈曲变形也变大;
- The concrete slabs strengthen the torsion buckling capacity of the steel grids and enhance the minimum geometric nonlinear buckling load. 混凝土面板加强了网架的抗扭转屈曲能力,提高了最小几何非线性屈曲荷载。
- It is shown that the convergence of solutions for the buckling load is good when the number of polynomials is more than 20. 解析表明屈曲载荷在多项式项数大于20以上时趋于稳定,可得到高精度的解。
- Three difference buckling modes of delaminated shell were considered.The nfluence of boundary condition, length and depth of delamination on buckling load was analyzed. 考虑脱层壳的三种不同屈曲模态,分析了边界条件、脱层长度、深度对脱层壳屈曲载荷的影响;
- The buckling load ration of the holed plate and integrity plate was gived.It was pointed out the buckling stress of the holed thin plate is smaller than it of the no holed plate. 其失稳临界应力与完整平板的结果作了比较,指出了开口对薄板失稳临界应力带来的影响。
- Finally, based on the tested and numerical analysis results, a formula to calculate the buckling load of composite pipes under axially compressive load is obtained by correcting Perry formula. 最后基于试验结果与数值分析结果,通过修正Perry稳定计算公式,得到了CFRP-铝合金组合长管屈曲荷载的计算公式。
- Based on this, the complex constraint method has been used to get the buckling load for the whole axisymmetric shell by solving the eigenvalue problem for only one substructure without introducing any additional approximation. 根据这一特点,采用复约束方法,通过求解单个子结构的屈曲方程得到了整个结构的屈曲载荷和模态,大大减小了所求解问题的规模,并且在此简化过程中没有引入任何附加的近似。
- Dynamic Plastic Buckling of Cylindrical Shells under Axial Impact 受轴向冲击圆柱壳的塑性动力屈曲研究
- Plastic buckling analysis of internal high-pressure forming 内高压成形塑性屈曲分析
- The variable regularity of buckling loads of double delaminated beam can be clearly explained from the isoline figure in this paper. 压屈载荷的等值线图可以清晰地描述任意双分层损伤层合梁的压屈载荷随分层位置的变化规律。
- flexural-torsional buckling load 弯扭屈曲荷载
- PLASTIC BUCKLES FOR GARMENT. SHOES,LUGGAGE SPROTSWARE ETC. PLASTIC FASTENERS FOR AUTOMOBILES HOMEAPPLIANCES,ELECTRONICS,INJECTION MOLDS. 有关服装、鞋类、运动用品之工程、塑胶扣具、汽车家电、电子工业之工程塑胶扣具、模具制造。
- The tension is easily adjusted using the black plastic buckle adjusters. These adjusters also make quick-release of the legs simple. 紧张容易地被调整使用黑塑料扣调整器。这些调整器并且使迅速解脱腿简单。
- Bind down the ropes around the load on the lorry. 把绕在卡车上货物外面的绳子扎紧。