您要查找的是不是：
- piston rod split pin 活塞杆开尾销
- split pin for set piston rod 活塞杆定位销
- Worn crankcase piston rod seals O-rings on. 曲轴箱柱塞连杆O型圈磨损或柱塞衬套磨损。
- Worn crankcase piston rod seals. 曲轴箱连杆密封件损坏。
- It is attached using a bolt and split pin. 它使用一个劈开销钉并且附上螺栓。
- Replace crankcase piston rod seals. Replace O-rings. 更换新的曲轴箱柱塞连杆O型圈。
- When assembling, leave the mark on body of piston rod frontward. 装配时，杆身上的记号要朝前。
- If any other requirements for piston rod head, U type ring width of cylinder lid, and diameter of pin are needed when placing an order, it is recommended to use our existing forged pieces. 订货的场合，如果对活塞杆头、油缸盖的U形环的宽度、销子的直径等尺寸方面另有要求时，建议采用能够利用的本公司现有的模锻件。
- Th e piston rod should befitted with the crosshead arenow going tryit. 活塞杆应与十字头孔配合。
- To ensure a secure connection between the arm and the disc nut, split pin is used. 为了确保臂杆和阀瓣螺母之间的安全连接,使用了开口销。
- A beam that connects the piston rod to the connecting rod of a reciprocating engine. 十字头连接活塞杆和往复式发动机连杆的横杆
- As the piston descended, a ratchet engaged the piston rod and engine shaft and thus power was transmitted. 当活塞下行时，棘轮连接活塞杆和发动机轴，因此将功率输送出去。
- High strength bolts for steel structure, bolts for diggers, hex bolts with split pin hole, bolts for automobile cylinder cap and non-standard components. 高强度钢结构螺栓,挖掘机螺栓,六角头绞制孔螺栓,汽车缸盖螺栓及非标准件。
- THE SEALING BETWEEN THE CRANKCASE AND SCAVENGING AIR BOXES IS ACHIEVED BY MEANS OF PISTON ROD STUFFING BOXES. 曲柄箱与扫气箱之间的密封是通过活塞杆填料函实现的。
- A hydraulic lock is installed on the vertical leg cylinder to avoid extending of the leg piston rod in operation. 在支腿垂直油缸上装有液压锁,能可靠地防止行驶时支腿活塞杆伸出。
- External diameter E and piston rod diameter D will not comply with the above standard due to different applications. 根据用途，缸体外径E，活塞杆直径d有时与上述尺寸不同。
- Miller of hardware of our the Yangtse River should produce small commodities " 2 hammers sell 3 needles " , namely the pin, clip, needle that order a book, yuan hammer, hobnail, split pin. 苏州是我国小商品生产的重要基地之一。我们长江五金厂主要生产小商品“三针二钉一销”,即大头针、回形针、订书针、元钉、鞋钉、开口销。钉头针脑,看起来不显眼,但与人民群众日常生活休戚相关。
- Gas piston rod and receiver. Note the recess on the bottom of the receiver, it is for the bolt locking. 导杆及枪匣，注意枪匣内下方的凹槽，供枪机闭锁用。
- An oscillating lever connected to an engine piston rod and used to transmit power to the crankshaft. 传动杆可摆动的杠杆，与引擎之活塞相连，用以向机轴传送能量
- In all designs, the valve stem normally serves as a piston rod with disc fastened directly to them. 在所有结构中，阀杆通常作为活塞杆，阀瓣直接固定在阀杆上。
